浓乳液模板法制备多孔二氧化碳吸附材料
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

北京市自然科学基金资助项目(2122046)


Preparation of Carbon Dioxide Adsorbent via Concentrated Emulsion Template
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    首先通过浓乳液模板法制备了多孔二氧化硅基体,然后采用物理浸渍法将聚乙烯亚胺引入到二氧化硅基体内,制备出一种氨基功能化的多孔二氧化硅材料。采用红外光谱、扫描电镜以及比表面积测试(BET)对材料的结构与形貌进行了表征,分析了浓乳液分散相体积分数对二氧化硅多孔结构的影响。最后研究了固载聚乙烯亚胺(PEI)的二氧化硅多孔材料的二氧化碳吸附性能。结果表明,随着浓乳液分散相体积分数的增加,聚苯乙烯模板材料的泡孔直径减小,由此制得的多孔二氧化硅的平均孔径减小,负载PEI后此种材料的比表面积、孔隙率和孔径均变小,最终所制备的多孔结构固体二氧化碳吸附材料具有吸附容量大与吸附可再生性好的特点,75℃最大吸附容量为3.28mmol/g。

    Abstract:

    The porous silica was fabricated according to the template polystyrene prepared via concentrated emulsion polymerization, and then polyethyleneimine was impregnated into porous silica. Finally, a kind of amino-functionalized porous silica was obtained. The structures and morphologies of the material were characterized by FT-IR, Brunauer Emmett Teller (BET) and SEM. The effect of the volume fraction of dispersed phase on concentrated emulsion was studied. The results show that with increase of the volume fraction of dispersed phase in concentrated emulsion, the cell diameter of polystyrene template is reduced, thereby producing a reduced average pore size of porous silica. The amine functionalized porous silica was applied as the carbon dioxide adsorbent, and the adsorption capacities are high and easily regenerated. The highest adsorption capacities of the absorbent can be up to 3.28 mmol/g at 75 ℃.

    参考文献
    相似文献
    引证文献
引用本文

杜衍辉,杜中杰,邹 威,密建国,王兆旭,张 晨.浓乳液模板法制备多孔二氧化碳吸附材料[J].高分子材料科学与工程,2014,30(6):33-37. Yanhui Du, Zhongjie Du, Wei Zou, Jianguo Mi, Zhaoxu Wang, Chen Zhang. Preparation of Carbon Dioxide Adsorbent via Concentrated Emulsion Template[J]. Polymer Materials Science & Engineering,2014,30(6):33-37.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-06-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司