SiO2/剑麻纤维素微晶的制备及对环氧树脂的改性
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51163004);广西自然科学基金资助项目(2013GXNSFAA019308);有色金属及材料加工新技术教育部重点实验室(12KF-10);广西高校人才小高地创新团队及广西特聘专家专项经费资助


Preparation of SiO2-Sisal Fiber Microcrystalline and the Modification of Epoxy Resin
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过溶胶-凝胶法,以正硅酸乙酯(TEOS)为硅源、乙醇为溶剂、盐酸为催化剂,在剑麻纤维素微晶(SFCM)表面包覆上了一层连续、致密的二氧化硅(SiO2),制得二氧化硅包覆剑麻纤维素微晶(SiO2-SFCM)。采用红外光谱和扫描电子显微镜对其结构进行表征,并与环氧树脂(EP)复合制备了SiO2-SFCM/EP复合材料,研究了SiO2-SFCM 对EP 复合材料力学性能的影响。结果表明,SiO2包覆层增强了SFCM 与EP 之间的界面相互作用,提高了复合材料的力学和热性能。当加入的SiO2-SFCM 的质量分数为3%时,复合材料的冲击强度由未改性的16.4kJ/m2 提高到29.4kJ/m2,热分解温度提高24℃,二氧化硅的包覆率为50%~60%。

    Abstract:

    Silica coated sisal cellulose microcrystalline(SiO2-SFCM), which has a layer of continuous, dense silica coated the sisal microcrystalline cellulose surface, was prepared by sol-gel method using tetraethylorthosilicate (TEOS) as silica precursor, ethanol as solvent and hydrochloric acid as catalyst. The structure of SiO2-SFCM was characterized by Fourier transform infrared spectroscopy (FT IR), scanning electron microscope (SEM), and the mechanical properties of the SiO2-SFCM/EP composites were investigated. The results show that the silica layer improves the interfacial interaction between SiO2-SFCM and epoxy resin (EP), which enhances the mechanical and thermal properties of the SiO2-SFCM/EP composites. By adding 3% SiO2-SFCM, the impact strength of the epoxy resin composites increases from 164 kJ/m2 to 294 kJ/m2 and the thermal decomposition temperature of modified systems is also 24 ℃ higher than that of the unmodified system. The cladding rate of silica coated is 50%~60%.

    参考文献
    相似文献
    引证文献
引用本文

肖仙娥,陆绍荣,祁 博,曾 岑,虞锦洪,杨利平. SiO2/剑麻纤维素微晶的制备及对环氧树脂的改性[J].高分子材料科学与工程,2014,30(6):170-173. Xian’e Xiao, Shaorong Lu, Bo Qi, Ceng Zeng, Jinhong Yu, Liping Yang. Preparation of SiO2-Sisal Fiber Microcrystalline and the Modification of Epoxy Resin[J]. Polymer Materials Science & Engineering,2014,30(6):170-173.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-06-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司