核壳结构丙烯酸酯共聚物的制备及对聚碳酸酯的增韧
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation of Acrylate Copolymer with Core-Shell Structure and Toughening of Polycarbonate
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用半连续乳液聚合方法制备了聚丙烯酸丁酯/聚甲基丙烯酸甲酯(PBA/PMMA)核壳结构乳液,经处理制得丙烯酸酯共聚物(ACR),再用ACR对聚碳酸酯(PC)进行增韧改性。研究了引发剂用量、乳化剂配比和用量、交联单体的用量对聚合物乳液的影响,以及ACR含量、核壳比、乳化剂用量和交联单体等对共混物力学性能的影响,并用扫描电镜对共混物冲击断面形貌进行了研究。实验结果表明,随乳化剂用量的增大,乳胶平均粒径减小。在乳化剂用量一定时,随乳化剂中OP-10的增加,乳胶平均粒径增大。在核壳结构乳液中核壳质量比为75/25,交联单体用量为8%,乳化剂用量为3%的条件下,共混物中ACR质量分数为6%时,共混物缺口冲击强度最大,使用交联单体二甲基丙烯酸丁二醇酯(BDDMA)的共混物缺口冲击强度是使用交联单体二甲基丙烯酸乙二醇酯(EGDMA)的共混物缺口冲击强度的2倍。随着ACR 含量的增加,PC/ACR 的缺口冲击强度增加,拉伸强度和弯曲强度略有下降。扫描电镜表明,ACR 在PC/ACR中分散粒径大于乳胶粒径。

    Abstract:

    Polybutyl acrylate (PBA)/ polymethyl methacrylate (PMMA) core-shell emulsions were prepared by semi-continuous emulsion polymerization. After further treatment of latex, the acrylate copolymer (ACR) was produced. Then polycarbonate (PC) was toughened with ACR. The effect of emulsifier content on the particle size of latex and the effect of ACR content, the ratio of PBA/PMMA, emulsifier content, different cross linking monomer on the mechanical property of PC/ACR blends and the impact fracture morphology of the blends were studied by SEM. The result show that the particles size of PBA/PMMA copolymer latex decreases with increase of the emulsifier content, and increases with increase of OP-10 content of emulsifier. With the ACR content of 6%, 3% emulsifier and m(PBA)/m(PMMA) of 75/25,using 8% butanediol dimethacrylate(BDDMA) as cross linking monomer, the notched impact strength of PC /ACR blends is 2 times of PC /ACR blends with ethylene glycol dimethyl acrylate (EGDMA) as cross linking monomer. The notched impact strength of PC /ACR blends increases with increase of the ACR content, tensile strength and flexural strength of PC/ACR blends less decrease with increase of the ACR content. SEM indicates that the particle size of ACR in the blends is greater than that in the core shell copolymer latex.

    参考文献
    相似文献
    引证文献
引用本文

陆 波,李 鹏,祁 娇,张 微.核壳结构丙烯酸酯共聚物的制备及对聚碳酸酯的增韧[J].高分子材料科学与工程,2014,30(7):24-30. Bo Lu, Peng Li, Jiao Qi, Wei Zhang. Preparation of Acrylate Copolymer with Core-Shell Structure and Toughening of Polycarbonate[J]. Polymer Materials Science & Engineering,2014,30(7):24-30.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-07-14
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司