含氨基的改性氟硅丙烯酸酯乳液的制备
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Synthesis of Acrylate Copolymer Emulsion Containing Fluoro-Silicon and Amino Group
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用半连续乳液聚合法在丙烯酸正丁酯(BA)、甲基丙烯酸甲酯(MMA)和乙烯基三乙氧基硅烷(VTES)共聚物上通过烷氧基水解缩合成功引入了含氟硅单体甲基三氟丙基环三硅氧烷D3F)及含氨基基团的Γ-氨基三乙氧基硅烷(KH550),得到的改性丙烯酸酯乳液可用于提高织物的疏水性能。通过正交实验得出了最佳反应工艺:反应温度为80℃、氟硅单体量占单体总质量的5%,KH550的量占单体总质量的4%,D3F的量占单体总质量的4%。对所获得乳液进行了红外、透射电镜、粒径和热重等一系列测试,结果表明,乳胶粒粒径分布均匀,大小在125nm 左右,热重表征得出熔融温度(Tmax)480℃,乳液涂覆在棉和真丝上与水的接触角达到了125.8°和120.7°。

    Abstract:

    1,3,5-Trimethyltris (3,3,3-trifluoropyropyl) cyclotrisiloxane (D3F) and Γ- aminopropyltriethoxysilane(KH550)were successfully introduced into the copolymer of butyl acrylate (BA), methyl methacrylate (MMA) and vinyltriethoxysilane(VTES) by the hydrolytic condensation of alkoxy. This will improve the waterproofness of the fabric. The best reaction process was obtained through the orthogonal experiment as follows: reaction temperature is 80 ℃, D3F is 25% of the total monomers and KH-550 is 4% of the total monomers. The obtained emulsion was tested by Fourier transform infrared (FT-IR) spectrometry, laser-particle-size analysis, transmission electron microscopy (TEM), differential scanning calorimeter (DSC), thermo-gravimetric analysis (TGA) and contact angle tester (CA). The results show that the emulsion particle size is about 125 nm, the temperature where the weight loses is the most (Tmax) is 480 ℃. When theemulsion is coated on silk and cotton, the water contact angle reaches 125.8° and 120.7°, respectively.

    参考文献
    相似文献
    引证文献
引用本文

薛 萍,许 琳,卞 余,谢洪德.含氨基的改性氟硅丙烯酸酯乳液的制备[J].高分子材料科学与工程,2014,30(8):156-160. Ping Xue, Lin Xu, Yu Bian, Hongde Xie. Synthesis of Acrylate Copolymer Emulsion Containing Fluoro-Silicon and Amino Group[J]. Polymer Materials Science & Engineering,2014,30(8):156-160.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-08-20
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司