轮胎胎面胶料挤出口型逆向数值设计
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省自然基金资助项目(BK2011405);江苏省高校自然科学研究面上项目(12KJB430006);江苏省普通高校研究生科研创新计划项目(CXZZ12_0666)


Inverse Numerical Design of Extrusion Die of Tread Rubber
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对某胎面胶(TMG)挤出断面与施工设计断面局部误差较大问题,利用Polyflow 软件,选取Phan-ThienandTanner(PTT)本构模型和Navier滑移模型,逆向数值设计了该胶料的挤出口型。分析口型出口形状的成因,针对口型出口处速度场分布不均这一结果,选取不同流道长度逆向设计口型并分析其对挤出质量的影响。结果表明,胶料在口型出口处沿挤出方向的速度分布决定了逆向设计口型的出口构型;流道长度对口型出口截面积、胀大比、沿挤出方向的速度分布以及压力分布影响显著;逆向设计口型挤出断面与施工设计断面具有很好的一致性。

    Abstract:

    Considering the larger relative error of local area of tire tread(TMG), the inverse numerical technique was used to design the extrusion die by selecting Phan-Thien and Tanner(PTT) constitutive equation and Navier slip equation with Polyflow. The die outlet was analyzed. Based on the uneven velocity distribution, channels of different lengths were selected to design die and analyze their influence on extrusion quality. The results show that the configuration of inverse designed die depends on the velocity distribution along extrusion direction at the exit; the effect of channel length on area of die outlet, swell ratio, the velocity distribution and pressure distribution is significant; the redesigned extrusion section has good agreement to the construction designed section.

    参考文献
    相似文献
    引证文献
引用本文

王国林,姜 波,李国瑞,岳 爽.轮胎胎面胶料挤出口型逆向数值设计[J].高分子材料科学与工程,2014,30(10):108-112. Guolin Wang, Bo Jiang, Guorui Li, Shuang Yue. Inverse Numerical Design of Extrusion Die of Tread Rubber[J]. Polymer Materials Science & Engineering,2014,30(10):108-112.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-10-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司