压缩对含β成核剂等规聚丙烯注塑样品皮芯结构的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(21273206)


Effect of Compression Process on the Skin-Core Structure of β-iPP Injection Samples
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    本文对含有β成核剂等规聚丙烯的注塑样品进行压缩,研究了不同压缩比、不同压缩温度条件下,注塑样品的皮芯结构变化情况。结果表明,当注塑样品压缩比达到一定临界值时,压缩可以消除注塑样品中晶体结构的不均一性,对于注塑iPP样品来说,该值介于2和4之间;随着压缩比的增大,样品中的β晶和α晶均被进一步破坏,总结晶度降低,晶体的取向度增加;随压缩温度的升高,β晶破坏明显,而α晶含量增加,晶体取向度均略微增大。

    Abstract:

    Series of β-iPP injection samples were treated by compressing with different ratio and temperature, and the difference of the microstructure between these samples was studied. It is found that, for these samples obtained: there should be a critical compressing ratio which might be between 2 and 4, and when it reaches that value the structure inhomogeneity can be removed; with increasing of the compressing ratio, both α-crystal and β-crystal are destroyed gradually, and the total crystallinity decreases but the crystal orientation rises; when the temperature rises, the destruction of β-crystal becomes more significant but the content of α-crystal increases, meanwhile, the relative orientation of these two crystals both improves slightly.

    参考文献
    相似文献
    引证文献
引用本文

卓然然,吴 杰,苏 磊,赵书俊.压缩对含β成核剂等规聚丙烯注塑样品皮芯结构的影响[J].高分子材料科学与工程,2014,30(10):117-121. Ranran Zhuo, Jie Wu, Lei Su, Shujun Zhao. Effect of Compression Process on the Skin-Core Structure of β-iPP Injection Samples[J]. Polymer Materials Science & Engineering,2014,30(10):117-121.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-10-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司