内衬聚偏二氟乙烯热塑功能层的玻璃纤维复合材料缠绕管弯曲性能测试评价
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展计划(863计划)项目(2012AA03A201);教育部科学技术研究重点项目(211007);天津市高等学校科技发展基金计划项目(2012ZD02)


Testing and Evaluation Flexural Properties of Composite Pipe with Glass Fiber Winding Reinforced with Polyvinylidene Fluoride-Lined
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    增强层缠绕角度和聚偏二氟乙烯(PVDF)表面粗糙度是影响内衬PVDF热塑功能层的玻璃纤维复合材料缠绕管弯曲性能的重要因素。采用3种规格的石英砂对PVDF管进行喷砂处理以获得不同的表面粗糙度,以PVDF管为芯模,采用湿法缠绕制作复合材料管。采用四点弯曲测试方法,测试分析如上2种因素对复合材料管弯曲性能的影响。结果表明,PVDF内衬层经过24mesh喷砂处理后,随者缠绕角度的增大,缠绕管的弯曲强度逐渐减小,而曲率半径先增大后减小,其中采用[+45/-45]4 缠绕结构的复合材料管曲率半径最小。随喷砂颗粒增大,复合材料管弯曲强度和曲率半径略有增大,弯曲失效后刚度退化趋于缓慢。

    Abstract:

    The winding angle of enhancement layer and the surface roughness of polyvinylidene fluoride(PVDF) are important factors, which affect flexural properties of glass fiber wound reinforced PVDF-lined composite pipes. Using three different sizes of quartz sand blasting on PVDF pipes, different surface roughness was got. PVDF tube used as mandrel, wet winding was applied to produce composites pipe. Use four-point bending test to analyze effect of these two factors on flexural properties of composite pipe. The results show as follows. Composite tube was produced with different winding angles and using 24 mesh sand blasted PVDF as mandrel. With increase of the winding angle, the pipe bending strength decreases, and the radius of curvature first increases and then decreases, which with [+45/-45]4 wound composite tube shows the smallest radius of curvature; as blasting particles increases,the bending strength and the radius of curvature increase slightly, the bending stiffness degradation after failure tends to slow.

    参考文献
    相似文献
    引证文献
引用本文

朱有欣,张国利,马小菲,陈光伟,孙 颖.内衬聚偏二氟乙烯热塑功能层的玻璃纤维复合材料缠绕管弯曲性能测试评价[J].高分子材料科学与工程,2014,30(10):122-127. Youxin Zhu, Guoli Zhang, Xiaofei Ma, Guangwei Chen, Ying Sun. Testing and Evaluation Flexural Properties of Composite Pipe with Glass Fiber Winding Reinforced with Polyvinylidene Fluoride-Lined[J]. Polymer Materials Science & Engineering,2014,30(10):122-127.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-10-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司