聚碳酸亚丙酯乳液的制备与性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

海南省自然科学基金资助项目(212020);海南省产学研一体化专项项目(CXY20130047,CXY20140041);海南大学化学工程与工艺专业卓越工程师培养计划


Preparation and Properties of Poly(Propylene Carbonate) Emulsion
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用直接乳化法制备聚碳酸亚丙酯(PPC)乳液,研究乳化剂亲水亲油平衡(HLB)值、连续相聚乙烯醇(PVA)浓度对乳液性能的影响。研究表明,当乳化剂HLB值在12.6~16.0之间时,均可制得PPC乳液。PVA质量分数高于1%则会导致PPC乳液稳定性下降。当乳化剂HLB值为13.0时,乳液白色泛蓝光,电导率为96.2μS/cm,固含量为3.73%,5000r/min下离心10min既无沉淀也无分层产生,静置半月无明显变化,粒径分布曲线分别在2μm 和30μm 处有2个独立的峰。

    Abstract:

    Poly (propylene carbonate) (PPC) emulsion was obtained successfully by the emulsification process. Effect of the emulsifier hydrophile-lipophile balance (HLB) value and polyvinyl alcohol (PVA) content of aqueous solution on the emulsion was researched. The results release that PPC emulsion could be successfully obtained when emulsifier HLB value is between 12.6 and 16.0. Increasing of PVA mass fraction above 1% will lead to decrease of the stability of the PPC emulsion. The white bluing PPC emulsion with the good stability would be got when the emulsifier HLB value is 13. Some properties of the PPC emulsion are listed as follow: the conductivity is 96.2 μS/cm, the solid content is 3.73%, no precipitation or stratification is produced by 5000 r/min centrifuging for 10 min. And in the experimental period, there is still no obvious change after half a month and two independent peaks appear in particle size distribution curves at the particle size of 2 μm and 30 μm.

    参考文献
    相似文献
    引证文献
引用本文

王陈曼,潘莉莎,李冬清,徐 鼐,庞素娟,张永明,林 强.聚碳酸亚丙酯乳液的制备与性能[J].高分子材料科学与工程,2014,30(10):144-148. Chenman Wang, Lisha Pan, Dongqing Li, Nai Xu, Sujuan Pang, Yongming Zhang, Qiang Lin. Preparation and Properties of Poly(Propylene Carbonate) Emulsion[J]. Polymer Materials Science & Engineering,2014,30(10):144-148.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-10-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司