不同链结构聚丙烯流延基膜的片晶结构及其拉伸成孔性
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省太阳能电池材料与技术重点实验室资助项目


Structures of Crystal Lamellar from PP Cast Films with Different Chain Structures and Their Influence on Microporous Membrane Formation by Uniaxially Stretching
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以重均相对分子质量和相对分子质量分布不同的4种聚丙烯树脂为基材,并在聚丙烯(PP)分子链上引入长链支化,通过熔融挤出得到流延基膜,经拉伸后形成微孔膜。采用凝胶渗透色谱、差示扫描量热、傅里叶变换红外光谱、扫描电镜等方法分析表征了PP树脂相对分子质量、相对分子质量分布和长链支化结构对PP流延基膜片晶结构和微孔膜结构的影响。结果表明,PP树脂相对分子质量增加可以使基膜片晶取向度增大,相对分子质量分布较窄的基膜具有更高的片晶取向度。流延基膜的取向片晶结构越完善,拉伸后形成的微孔数量越多,孔分布越均匀。微孔膜结构也与片晶间连接链密度以及长短连接链比例有关,适当比例的长短连接链分布可以获得较好的孔形态。在线型PP中添加少量长链支化聚丙烯(LCB-PP)可以改善基膜的取向片晶结构,提高微孔膜的孔隙率和透气性,但LCB-PP含量较高时导致片晶取向度下降,孔隙率和透气性下降。

    Abstract:

    Four kinds of PP resins with different weight-average molecular weights and molecular weight distributions and PP resin with different long chain branching (LCB) levels were selected to develop precursor films through casting film process and then to form microporous membranes by stretching. The effects of molecular weight, molecular weight distribution and LCB-level on the structure of crystal lamellae in the precursor films and microporous membrane formation were investigated by gel permeation chromatography (GPC), differential scanning calorimetry (DSC), Fourier transform infrared spectrum (FT-IR), scanning electron microscope (SEM) and other methods. It is found that raising molecular weight of PP leads to an increase of lamellar orientation in the precursor film, and precursor films with higher lamellar orientation could be obtained from PP resins with narrow molecular weight distribution. More perfect the row-nucleated lamellar crystalline structure in the precursor film, the more micropores would be created and more uniformly distributed in the microporous membrane by stretching. The structure of microporous membranes was also related to the inter-lamellar tie chain density and proportion of long and short tie chains. Good microporous morphology could be formed by appropriate distribution of long and short tie chains. Introducing LCB-PP into linear PP resin improves row-nucleated lamellar structure in the precursor film, and increase porosity and permeability of the resulting membranes. However, high level of LCB reduces lamellar orientation in the precursor film, leading to decrease of porosity and permeability in the microporous membranes.

    参考文献
    相似文献
    引证文献
引用本文

蒋 姗,沈 鹏,谢 洵,朱梦冰,丁永红,俞 强.不同链结构聚丙烯流延基膜的片晶结构及其拉伸成孔性[J].高分子材料科学与工程,2014,30(11):98-102. Shan Jiang, Peng Shen, Xun Xie, Mengbing Zhu, Yonghong Ding, Qiang Yu. Structures of Crystal Lamellar from PP Cast Films with Different Chain Structures and Their Influence on Microporous Membrane Formation by Uniaxially Stretching[J]. Polymer Materials Science & Engineering,2014,30(11):98-102.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-11-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司