水辅助注塑气泡与二次穿透的分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51103037);江西省自然科学基金资助项目(2010GQC0029)


Analysis of Air Bubble and Secondary Penetration of Water in Water Assisted Injection Molding Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    水辅助注塑产品中容易出现气泡缺陷及二次穿透现象。文中通过实验与理论分析相结合的方法揭示了水辅助注塑制件内壁面气泡现象产生的主要根源并不是水的气化,而是注水装置设计或工艺的缺陷导致注水前注水通道中存在空气,注水时空气与水一同注入所致。只需改进注水装置,保证注水时是纯水注入就可避免气泡缺陷的产生。同时采用实验手段分析了二次穿透的产生原因及具体形成过程,并与气体辅助注塑的二次穿透进行了比较。探究了熔体预填充量对二次穿透的影响,可通过精确控制熔体预填充量或在制件末端设置小段类似溢料腔的结构来消除或改善二次穿透。

    Abstract:

    Air bubbles and secondary penetrating phenomenon occur frequently in water assisted injection molding (WAIM) product. The cause of generation of air bubbles in the residual wall thickness of WAIM parts was revealed by a combination of experimental and theoretical analysis methods. Its reason is not water gasification, but the air existing in the water injection channels as a result of defects of the water injection device design or process. The injection of air and water during the water injection stage leads to air bubbles. To avoid the air bubbles defect, water injection device needs to be improved and ensures only water be injected. The forming mechanism of secondary penetration was analyzed by experiments. The secondary penetration of WAIM process was compared with that of gas assisted injection molding (GAIM) process. The influence of short shot size of polymer melt on the secondary penetrating was investigated. To eliminate or improve secondary penetration, short shot size of polymer melt should be controlled precisely or a small structure just like an overflow cavity should be affiliated at the end of product.

    参考文献
    相似文献
    引证文献
引用本文

匡唐清,余春丛,邓 洋,黄淑慧.水辅助注塑气泡与二次穿透的分析[J].高分子材料科学与工程,2014,30(11):112-116. Tangqing Kuang, Chuncong Yu, Yang Deng, Suhui Huang. Analysis of Air Bubble and Secondary Penetration of Water in Water Assisted Injection Molding Process[J]. Polymer Materials Science & Engineering,2014,30(11):112-116.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-11-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司