层层自组装聚丙烯隔膜的表面改性
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省太阳能电池材料与技术重点实验室资助项目


Surface Modification of Polypropylene Membrane by Layer-by-Layer Self-Assembly
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    用层层自组装技术在锂电池用聚丙烯(PP)隔膜表面引入聚二烯丙基二甲基氯化铵(PDM)和丙烯酸-丙烯酸钠共聚物P(AA-co-AANa),获得具备良好亲水性、低热收缩率的复合隔膜。考察聚合物配比、自组装层数、温度等对隔膜表面结构和性能的影响。采用全反射傅里叶变换红外光谱和原子力显微镜分别表征膜表面组成和形貌。比较PP隔膜和复合隔膜各项测试结果发现,经自组装后,隔膜的表面水接触角可从90.6°降低至30.5°,130℃时的热收缩率由12%下降至9.4%。

    Abstract:

    In order to improve hydrophilicity and safety of polypropylene (PP) separator, poly (diallyl dimethyl ammonium chloride) and acrylic acid-sodium acrylate copolymer were introduced to the membrane surface by layer-by-layer self-assembly. The influences of polymer ratio, self-assembled layers and temperature on the surface structure and performance of membranes were studied. FT-IR and atomic force microscopy (AFM) were applied to characterize the surface composition and morphology of membranes. The permeability, shrinkage and contact angle of self-assembled membranes were tested. The results show that composite membranes own higher hydrophilicity and lower shrinkage. The water contact angle of PP separator decreases from 90.6°to 30.5°, while the shrinkage decreases from 12% to 9.4%.

    参考文献
    相似文献
    引证文献
引用本文

蒋 姗,李夏倩,丁永红,俞 强.层层自组装聚丙烯隔膜的表面改性[J].高分子材料科学与工程,2014,30(11):132-138. Shan Jiang, Xiaqian Li, Yonghong Ding, Qiang Yu. Surface Modification of Polypropylene Membrane by Layer-by-Layer Self-Assembly[J]. Polymer Materials Science & Engineering,2014,30(11):132-138.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-11-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司