丙烯腈-丙烯酸甲酯微孔膜的制备及成膜性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

天津市应用基础与前沿技术研究计划青年基金(13JCQNJC02300);第55批博士后面上资助项目(2014M551026);高等学校国家级大学生创新创业训练计划项目(201210058028)


Preparation and Properties of Poly(Acrylonitrile-co-Methyl Acrylate) Membrane
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以摩尔比为85/15的可熔融丙烯腈-丙烯酸甲酯共聚物(85/15AN-MA)为膜基体,用γ-丁内酯(γ-BA)和三乙酸甘油酯(GTA)复配作为混合稀释剂,采用热致相分离(TIPS)法制备了AN-MA 基微孔膜。详细研究了聚合物浓度、混合稀释剂的配比和冷却速率对微孔膜的孔结构、孔隙率、水通量及力学性能的影响。研究结果表明,随着γ-BA 含量的增加或凝固浴温度升高,微孔膜成型过程中存在小部分非溶剂致相分离(NIPS),形成不对称的横截面结构。增加GTA 的比例或快的冷却速率更利于发生TIPS,γ-BA的质量分数为45%和50%时,微孔膜发生单纯的TIPS过程,凝固浴为0℃的乙醇浴时,AN-MA微孔膜具有更好的力学性能。

    Abstract:

    Melt processable poly(acrylonitrile-co-methyl acrylate) (AN-MA) with mole ratio of 85:15 synthesized by emulsion polymerization was used as raw stuff. Gamma butyrolactone (γ-BA) and glyceryl triacetate (GTA) were used as mixed diluent, in which γ-BA was used as solvent and GTA as nonsolvent. A systematic study was carried out about the effects of polymer contents, diluent ratio and cooling rates on the membrane structure, porosity, water flux and mechanical properties. AN-MA membranes were mainly prepared via thermally induced phase separation (TIPS) process. With increasing of the γ-BA content or coagulation bath temperature, there is a small part of non-solvent induced phase separation (NIPS) existing during formation of the membrane, which leads to a cross section structure asymmetrically. It is shown that increasing GTA content or cooling rate favors TIPS process. TIPS process happens merely with the γ-BA mass fraction of 45% and 50% in the mixed diluent. The membranes formed in ethanol bath at 0 ℃ possess more superior mechanical properties.

    参考文献
    相似文献
    引证文献
引用本文

熊俊诚,韩 娜,王争争,陈素梅,张兴祥,王 栋,王 宁,李 伟.丙烯腈-丙烯酸甲酯微孔膜的制备及成膜性能[J].高分子材料科学与工程,2014,30(11):168-174. Juncheng Xiong, Na Han, Zhengzheng Wang, Sumei Chen, Xingxiang Zhang, Dong Wang, Ning Wang, Wei Li. Preparation and Properties of Poly(Acrylonitrile-co-Methyl Acrylate) Membrane[J]. Polymer Materials Science & Engineering,2014,30(11):168-174.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-11-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司