内嵌聚偏氟乙烯热塑层的纤维增强热固性复合材料管压缩性能测试评价
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展计划(863计划)项目(2012AA03A201);教育部科学技术研究重点项目(211007); 天津市高等学校科技发展基金计划项目(2012ZD02)


Compressive Properties Testing and Evaluation of Fiber-Reinforced Thermoset Composites Pipe Embedded with Thermoplastic Polyvinylidene Fluoride
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    内嵌聚偏氟乙烯(PVDF)表面粗糙度、增强层厚度和缠绕角度是影响内嵌PVDF热塑层的纤维增强热固性复合材料管压缩性能的重要因素。以24 mesh石英砂表面喷砂处理后的内嵌PVDF管为芯模,采用湿法缠绕技术制备不同结构参数的复合材料管。采用压缩实验测试分析如上3种因素对复合材料管压缩性能的影响,并分析其破坏模式与失效机理。结果表明,PVDF经24 mesh喷砂处理后制备的复合材料管压缩强度提高了34.6%,压缩模量减小了46.2%;随增强层厚度的增加,压缩强度逐渐减小后趋于稳定,压缩模量先减小后增大到最大值;随缠绕角度的增大,压缩强度和压缩模量逐渐减小。

    Abstract:

    Surface roughness of embedded polyvinylidene fluoride (PVDF), winding thickness of enhancement layer and winding angle are important factors for compression properties of composites pipe. Using PVDF pipe blasted with quartz of 24 mesh sizes sand as mandrel, wet winding was applied to produce composites pipe. The compression test method was used to test the above three factors how to affect the compression properties of composite pipe; the failure mode and failure mechanism was summarized. The results show that the compression strength of composite pipe produced with 24 mesh sand blasted PVDF is increased by 34.6%, compression modulus is decreased by 46.2%; with the thickness of enhancement layer increasing, compression modulus decreases and then increases to the maximum value; with the winding angle increasing, the compression strength and compression modulus gradually decrease.

    参考文献
    相似文献
    引证文献
引用本文

朱有欣, 张国利, 马小菲, 陈光伟, 孙颖.内嵌聚偏氟乙烯热塑层的纤维增强热固性复合材料管压缩性能测试评价[J].高分子材料科学与工程,2014,30(12):88-93. Youxin Zhu, Guoli Zhang, Xiaofei Ma, Guangwei Chen, Ying Sun. Compressive Properties Testing and Evaluation of Fiber-Reinforced Thermoset Composites Pipe Embedded with Thermoplastic Polyvinylidene Fluoride[J]. Polymer Materials Science & Engineering,2014,30(12):88-93.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-12-12
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司