超声粉末模压成型超高分子量聚乙烯微塑件的两相结构
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51175348,54105306,51375315)


Two-Phase Structure of Micro Ultrasonic Powder Molding Ultra-High Molecular Weight Polyethylene Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    应用了一种新颖的微型超声粉末模压成型方法(micro-UPM)成型超高分子量聚乙烯(UHMWPE)微塑件。先利用超声振动使UHMWPE粉末自身快速加热并塑化,之后在合模压力下快速充填微型腔,成功制备了多种规格的微塑件。差示扫描量热实验结果表明,micro-UPM UHMWPE微塑件为两相状态,由初生态和熔化-再结晶态两相组成。在超声塑化时间为0.5~1.5 s的范围内,熔化-再结晶相熔融峰面积逐渐增大,而初生态相熔融峰面积逐渐缩小,结晶度逐渐减小。当超声塑化时间为1.5 s时,微塑件结晶度达到最小值54.3%,而熔化-再结晶相分数达最大值98.3%,micro-UPM UHMWPE微塑件塑化质量最佳。单晶X射线衍射实验表明,微塑件中间区的结晶度数值比表层大,与普通注塑成型的微塑件相比,micro-UPM微塑件的结晶取向性不明显。

    Abstract:

    Through micro ultrasonic powder molding (micro-UPM), micro semi-crystalline polymer parts were formed. By the proposed method, semi-crystalline polymer powder was rapidly heated and plasticized by ultrasonic vibration, after which the microcavity was filled with the melt under sonotrode pressure (pu) to form a variety of micro polymer parts. Differential scanning calorimetry, scanning electron microscopy, and nanoindentation tests demonstrate that micro-UPM ultra-high molecular weight polyethylene (UHMWPE) parts consist of nascent and melt-recrystallized phases. Different tu (0.5~1.5 s) values are utilized to form UHMWPE parts at pu of 16 MPa and the holding time of 5.0 s. As tu increases, a rise in the melting peak of the melt-recrystallized phase and a drop in the melting peak of the nascent phrase as well as crystallinity are further observed. When tu is only 1.5 s, the crystallinity of the micro plastic part reaches the minimum value of 54.3% and the melt-recrystallized phase fraction fR reaches the maximum value of 98.3%. Powder particle interfaces almost disappear in this case, and optimum quality of the micro UPM UHMWPE part is achieved. Single-crystal XRD tests demonstrate that the crystallinity in the core region of the micro polymer part is higher than that in the skin region. Compared with conventional microinjection plastic parts, the crystal orientation of micro-UPM polymer parts is less obvious.

    参考文献
    相似文献
    引证文献
引用本文

梁雄, 伍晓宇, 李兵, 曾昆, 徐斌, 罗烽.超声粉末模压成型超高分子量聚乙烯微塑件的两相结构[J].高分子材料科学与工程,2014,30(12):103-107. Xiong Liang, Xiaoyu Wu, Bing Li, Kun Zeng, Bin Xu, Feng Luo. Two-Phase Structure of Micro Ultrasonic Powder Molding Ultra-High Molecular Weight Polyethylene Parts[J]. Polymer Materials Science & Engineering,2014,30(12):103-107.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-12-12
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司