聚对苯二甲酰对苯二胺多孔膜的制备及表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

973计划(2012CB722706);中国纺织工业联合会应用基础研究项目资助


Fabrication and Characterization of Poly(p Phenylene Terephthamide) Porous Membranes
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以浓硫酸为溶剂,聚乙二醇(PEG)为致孔剂,采用溶液相转化法制备了聚对苯二甲酰对苯二胺( PPTA)多孔平板膜,考察了膜的纯水通量、力学强度、截留率等性能,并用场发射扫描电子显微镜观察膜形貌。结果表明,所得PPTA多孔膜为具有不对称结构的非均质膜,上表面(自由面)为致密层,下表面(玻璃板面)为多孔层,可观察到原纤化微孔结构,膜横截面存在典型的溶出指状孔。随PPTA含量降低、致孔剂相对分子质量和凝固浴温度提高,膜通透性均随之相应有所提高。PPTA多孔膜对卵清蛋白溶液截留率达90%以上,对油水乳化液截留率可达70%以上。

    Abstract:

    Poly(p-phenylene terephthamide)(PPTA) porous membranes were fabricated via wet phase-inversion method using concentrated sulphuric acid (H2SO4) as solvent and polyethylene glycol (PEG) as pore-creating agent. Ultrafiltration performances of the membranes were characterized in terms of pure water flux, mechanical strength, rejection rate. The morphologies of PPTA membrane were observed by field emission scanning electron microscope(FESEM). The results show that the PPTA porous membrane is a kind of asymmetrical membrane, which has dense upper surface.The dissolved pore-creating agent brings about the fibrillar of microporous structure on the lower surface. Decrease of the PPTA content, increase of the molecular weight, and the promotion of coagulation bath temperature would bring about an obvious enhancement of the pure water flux and porosity. Moreover, the mechanical properties become worse as rising of coagulation temperature. Besides, the rejection rate of ovalbumin reaches more than 90%, while, that of the oily water reaches more than 70%.

    参考文献
    相似文献
    引证文献
引用本文

王纯, 肖长发, 黄庆林.聚对苯二甲酰对苯二胺多孔膜的制备及表征[J].高分子材料科学与工程,2014,30(12):149-154. Chun Wang, Changfa Xiao, Qinglin Huang. Fabrication and Characterization of Poly(p Phenylene Terephthamide) Porous Membranes[J]. Polymer Materials Science & Engineering,2014,30(12):149-154.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2014-12-12
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司