酶解木质素/炭黑复合补强体系对丁腈橡胶的补强性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家杰出青年科学基金(20925622);国家自然科学基金资助项目(21006036);973项目(2010CB732205);国家国际科技合作专项(2013DFA41670)


Reinforcing Properties of Enzymatic Hydrolysis Lignin/Carbon Black Composite Filler System for Acrylonitrile Butadiene Rubber
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用球磨法、气流粉碎法、喷雾干燥法分别处理酶解木质素(EHL),其中气流粉碎酶解木质素的比表面积最大,达到6311 m2/g,但仍然远低于炭黑N660的比表面积。将3种预处理方法制备的酶解木质素分别与炭黑对丁腈橡胶(NBR)进行复合补强,发现气流粉碎EHL的比例为50%的硫化胶的力学性能最优:拉伸强度、扯断伸长率比球磨法的分别高出17.28%,11.11%。该硫化胶的拉伸强度(20.44 MPa)、撕裂强度,比纯炭黑/NBR的分别略降低22.96%,12.03%;而扯断伸长率则提高28.50%,胶料仍具有优良的力学性能。但是随着复合补强体系中酶解木质素比例的逐步提高,NBR硫化胶的拉伸强度、撕裂强度都呈下降趋势。

    Abstract:

    Three methods viz. ball milling (BM), jet milling (JM) and spray drying (SD) were utilized to pretreat enzymatic hydrolysis lignin (EHL). The largest specific surface area of 6311 m2/g was obtained by the jet milling lignin (EHL-JM), which is far less than that of carbon black (CB) N660. The varied-treated EHL and CB were applied to reinforce acrylonitrile butadiene rubber (NBR). The results show that when the EHL-JM mass ratio is 50%, the NBR/EHL-JM/CB vulcanizate owns the best mechanical properties; its tensile strength and elongation at break are 17.28% and 11.11% higher than those of NBR/EHL-BM/CB, respectively. The tensile strength (20.44 MPa) and tear strength of the NBR/EHL-JM/CB blend are just 22.96% and 12.03% lower than those of NBR/CB vulcanizate; the elongation at break increases by 28.50%, reversely, revealing the vulcanizate still has good mechanical properties. However, with the ratio of EHL-JM in the composite filler system increasing, the tensile strength and tear strength of the NBR/EHL/CB blend decrease gradually.

    参考文献
    相似文献
    引证文献
引用本文

莫贤科, 周明松, 楼宏铭, 杨东杰, 邱学青.酶解木质素/炭黑复合补强体系对丁腈橡胶的补强性能[J].高分子材料科学与工程,2015,31(1):51-56. Xianke Mo, Mingsong Zhou, Hongming Lou, Dongjie Yang, Xueqing Qiu. Reinforcing Properties of Enzymatic Hydrolysis Lignin/Carbon Black Composite Filler System for Acrylonitrile Butadiene Rubber[J]. Polymer Materials Science & Engineering,2015,31(1):51-56.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-02-01
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司