螺杆类型对玻纤增强阻燃聚己二酰丁二胺二次料力学和热学性能的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(U1333126);广东省高校优秀青年创新人才培养计划资助项目(N9100210)


Effect of Screw Type on the Mechanical and Thermal Properties of Recycled Glass Fiber Reinforced Flame-Retarded Polyamide46
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过研究挤出过程中螺杆类型的变化对玻纤增强阻燃聚己二酰丁二胺二次料(RGFFRPA46)的玻纤长度、力学、热学性能的影响。结果说明,采用长径比为4.3∶1的单螺杆挤出后,RGFFRPA46的玻纤平均长度和力学性能下降幅度分别为4.4%和3.6%,热性能下降不明显。随着单螺杆长径比增加为40∶1,RGFFRPA46在挤出过程的停留时间加长,受到剪切作用增加,导致RGFFRPA46挤出后的玻纤平均长度、力学和热学性能下降幅度增加。当RGFFRPA46采用螺杆长径比30∶1、直径为30 mm的双螺杆挤出后,其玻纤平均长度和力学性能下降幅度分别达到了33.2%和23%,并且热学性能降低幅度最大。

    Abstract:

    When glass fiber(GF) reinforced flame-retarded polyamide46 (GFFRPA46) was injection molding once, the recycled GFFRPA46 (RGFFRPA46) including the scraps and unqualified injection products was granulated by different extruders with varying screw configurations. GF of the RGFFRPA46 samples was observed by SEM and the size of more than 1000 GF were calculated. The average length (L) and the percentage of GF, of which the length is higher than the critical length (Vj), decrease with increase of the screw diameter and the length to diameter ratio (L/D). The extruded RGFFRPA46 prepared by a single screw extruder with 70 mm screw diameter and 4.3 L/D obtains the excellent mechanical properties, compared to those of RGFFRPA46, and the decrease ratio is lower than 3.6%. Moreover, its thermal properties are not significant different from those of RGFFRPA46. When RGFFRPA46 was extruded by a twin screw extruder, the L, the mechanical and thermal properties of the extruded RGFFRPA46 decrease significantly.

    参考文献
    相似文献
    引证文献
引用本文

彭华乔, 蒋果, 谈灵操, 黄汉雄, 张水洞.螺杆类型对玻纤增强阻燃聚己二酰丁二胺二次料力学和热学性能的影响[J].高分子材料科学与工程,2015,31(1):103-107. Huaqiao Peng, Guo Jiang, Lingcao Tan, Hanxiong Huang, Shuidong Zhang. Effect of Screw Type on the Mechanical and Thermal Properties of Recycled Glass Fiber Reinforced Flame-Retarded Polyamide46[J]. Polymer Materials Science & Engineering,2015,31(1):103-107.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-02-01
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司