等规聚丙烯微注塑制品的力学性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(11372287);国家基础研究项目(2012CB626809)


Mechanical Properties of Micro Injection Molded Isotactic Polypropylene Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用等规聚丙烯材料,选取弹性模量和屈服强度作为微制品力学性能的指标,基于正交实验设计进行微注塑成型实验以成型微拉伸试样,采用直观分析、信噪比分析及方差分析对微试样的拉伸实验结果进行分析,研究工艺参数对厚度1.0mm,0.5mm 和0.2mm 的微注塑制品力学性能的影响规律及重要性,并分析尺度效应对微制品力学性能的影响。实验结果表明,不同尺度下,各个工艺参数对微制品力学性能的影响规律和重要性均不同,且随着尺寸的减小,微注塑制品的拉伸屈服强度增大,弹性模量增大。

    Abstract:

    The micro injection molding experiments were conducted based on design of experiments(DOE) method to mold the micro tensile specimens, and the elastic modulus, yield strength of the micro injection molded isotactic polypropylene parts were chosen as the mechanical property indexes. The influence of process parameters on the mechanical properties of the microparts with the thickness of 1.0 mm, 0.5 mm and 0.2 mm was analyzed based on the experiments results by intuitive analysis, signal to noise ratio analysis and variance analysis method, and the influence laws and significance of process parameters on the mechanical properties were obtained. The scale effect on the mechanical properties of the microparts was also investigated. The experimental results indicate that the influence rules and significance of the process parameters are different under different scale, and the yield strength and the modulus of the micro injection molded parts both increase with the scale decreasing.

    参考文献
    相似文献
    引证文献
引用本文

张建波,王利霞,王心超,刘晓东,蒋 林,卞 宁,张 扬,李 倩.等规聚丙烯微注塑制品的力学性能[J].高分子材料科学与工程,2015,31(2):124-129. Jianbo Zhang, Lixia Wang, Xinchao Wang, Xiaodong Liu, Lin Jiang, Ning Bian, Yang Zhang, Qian Li. Mechanical Properties of Micro Injection Molded Isotactic Polypropylene Parts[J]. Polymer Materials Science & Engineering,2015,31(2):124-129.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-02-23
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司