Fe3O4气凝胶/超支化环氧化合物/环氧树脂复合材料的固化行为及性能表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

总装预研项目基金(5312040303)


Curing Behavior and Properties of Fe3O4 Areogels/ Epoxidized Hyperbranched Polyesters/Epoxy Resin Systems
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用非等温差示扫描量热法(DSC)对Fe3O4气凝胶/超支化环氧化合物(EHBP)/环氧树脂(EP)固化体系的固化反应热行为及固化动力学进行了研究。分别利用Kissinger和Ozawa动力学模型计算得到各体系固化反应的表观活化能,并利用Crane模型计算出固化反应级数为一级反应;通过固化体系的DSC数据确定了体系的固化工艺为100 ℃2h→120 ℃2h→140 ℃1.5h;通过确定的工艺参数制备了Fe3O4气凝胶/EHBP/EP复合材料并进行了力学及吸波性能测试。结果表明,添加较低含量的Fe3O4气凝胶填料可保持纯环氧树脂基体的力学性能及低密度,同时在此基础上材料具有吸波性能,当Fe3O4气凝胶质量分数为1%时,Fe3O4气凝胶/EHBP/EP复合材料的拉伸强度为61.67 MPa,冲击强度为16.36 kJ/m2,密度为1.204 g/cm3,8~18 GHz的范围内的反射率均小于-10dB。

    Abstract:

    Curing process and curing kinetics of Fe3O4 areogels/epoxidized hyperbranched polyesters (EHBP)/epoxy resin (EP) systems were investigated by the non-isothermal DSC under different heating rates. Apparent activation energy of the curing systems was calculated by Kissinger method and Ozawa method respectively, and the reaction order was calculated according to Crane formula. Based on the DSC data, the curing process of the curing systems is 100 ℃ 2h→120 ℃ 2h→140 ℃ 1.5h, and the mechanical properties of the composites according to the curing processes were tested by the mechanics performance test. The results indicate that the lower content of Fe3O4 areogels could keep excellent mechanical properties of epoxy resin. When the mass fraction of Fe3O4 areogels is 1%, the tensile strength and impact strength are 61.67 MPa and 16.36 kJ/m2, respectively, the density is 1.204 g/cm3,and the reflectivity is below -10 dB in the range of 8~18GHz.

    参考文献
    相似文献
    引证文献
引用本文

张雅, 柴春鹏, 罗运军, 王鲁, 李国平. Fe3O4气凝胶/超支化环氧化合物/环氧树脂复合材料的固化行为及性能表征[J].高分子材料科学与工程,2015,31(3):88-93. Ya Zhang, Chunpeng Chai, Yunjun Luo, Lu Wang, Guoping Li. Curing Behavior and Properties of Fe3O4 Areogels/ Epoxidized Hyperbranched Polyesters/Epoxy Resin Systems[J]. Polymer Materials Science & Engineering,2015,31(3):88-93.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-03-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司