聚乳酸/聚己内酯复合发泡材料的制备及性能表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

2011年江苏省教育厅产学研推进项目(JHB2012-2);2012年江苏省科技厅工业支撑项目(BE2012169)


Preparation and Characterization of Polylactic Acid/Polycaprolactone Foamed Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    选用聚己内酯(PCL)与聚乳酸(PLA)进行共混改性,经挤出、发泡制备出性能良好的PLA/PCL复合泡沫板材。经红外光谱分析、断口扫描电镜、力学性能测试及差示扫描量热分析分别探究了PCL含量对复合发泡材料发泡效果、力学性能及结晶性能的影响。结果表明,PCL的加入能有效改善复合发泡材料的发泡效果。当PCL含量为10%时,试样的综合性能最优,冲击强度、压缩强度分别达到了8.9 kJ/m2,31 MPa;平均泡孔直径则由未改性发泡体系的2.8 mm降低至1.1 mm;结晶度由12.68%上升到17.95%,得到了泡孔尺寸小,分布均匀,表面质量佳,综合力学性能优良的复合发泡材料。

    Abstract:

    Polylactic acid (PLA) was mixed with its new modified polymer, polycaprolactone (PCL), to prepare composite foam with good performance through extruding and foaming. Series of characterizations including XRD, SEM analysis, mechanical properties test and DSC were used to investigate the effect of PCL content on the performances of the composite foam. The results show that PCL can improve the effect of foaming significantly. Through the integrated analysis, the best formulation of PCL is 10%. The impact strength and compressive strength grow up to 8.9 kJ/m2 and 31 MPa respectively. The average cell diameter decreases from 2.8 mm to 1.1mm, and the crystallinity rises from 12.68% to 17.95%. Finally, a kind of foamed composites was obtained which has excellent comprehensive mechanical properties due to small cell size and uniform distribution.

    参考文献
    相似文献
    引证文献
引用本文

孔颖, 姚正军, 周金堂, 姚芮.聚乳酸/聚己内酯复合发泡材料的制备及性能表征[J].高分子材料科学与工程,2015,31(3):94-99. Ying Kong, Zhengjun Yao, Jintang Zhou, Rui Yao. Preparation and Characterization of Polylactic Acid/Polycaprolactone Foamed Composites[J]. Polymer Materials Science & Engineering,2015,31(3):94-99.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-03-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司