无针喷头熔体静电纺丝制备取向纤维
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

北京市自然科学基金资助项目(2141002)


Fabrication of Oriented Fibers via Needleless Melt Electrospinning
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用无针喷头熔体静电纺丝装置制备取向纤维,以ANSYS电场模拟为指导,探究了纺丝距离、辊筒转速及电场强度等工艺条件对纤维结构的影响。当纺丝距离为20 mm时,其电场强度相对最大,但其纤维直径却较50 mm,80 mm粗。确定出本实验熔体电纺制备PP取向纤维的最佳距离为50~100 mm,并明确了接收辊筒转速对纤维取向度及纤维直径有显著的改善作用。通过扫描电镜、X射线衍射、差示扫描量热仪及拉伸试验对熔体电纺纤维进行性能表征,取向纤维膜孔径比随机纤维小得多,有利于提高过滤效率及制备超疏水纤维,热压后纤维结晶性变好,且致密性及力学性能均有所提高。

    Abstract:

    The oriented polypropylene fibers in this article were fabricated via the needleless melt electrospinning technique. Guided by an electric field simulation with the software ANSYS, then combined with experimental study to investigate the influence of the nozzle-to-electrode distance, the rotating speed and the electrical field strength on fiber structure. When the distance of nozzle-to-electrode is 20 mm, fiber diameters are relatively big even if the electric field intensity is relatively large. Determined an appropriate distance to electrospun oriented fibers which is in the range of 50~100 mm, and clearly knew that the increasing cylinder speed makes fiber orientation become better and fiber diameter become thinner. The properties of the fibers were studied by SEM, DSC, and XRD. The pore size of oriented membrane is much smaller than that of random membrane, which could be used to fabricate super-hydrophobic membranes and improve filtration efficiency. The crystal properties and mechanical properties of hot-pressing fibers are all improved than the native fibers.

    参考文献
    相似文献
    引证文献
引用本文

李小虎, 杨卫民, 丁玉梅, 李好义, 张有忱.无针喷头熔体静电纺丝制备取向纤维[J].高分子材料科学与工程,2015,31(3):133-137. Xiaohu Li, Weimin Yang, Yumei Ding, Haoyi Li, Youchen Zhang. Fabrication of Oriented Fibers via Needleless Melt Electrospinning[J]. Polymer Materials Science & Engineering,2015,31(3):133-137.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-03-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司