增塑剂乙酰聚合甘油不饱和脂肪酸多酯的合成及应用
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家“十二五”科技支撑计划(2012BAD32B05);中国林科院林业新技术研究所基本科研业务费重点项目(CAFINT2013K01)


Synthesis and Application of Acetylated Polyglycerol Unsaturated Fatty Acid Esters
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以自制二聚甘油和油酸为原料进行酯化反应合成聚甘油不饱和脂肪酸多酯,再与乙酸酐反应得到乙酰聚甘油不饱和脂肪酸多酯。采用单因素试验研究反应温度、反应时间、聚甘油与油酸摩尔比、催化剂用量对酯化率的影响,确定最优合成工艺条件为反应温度215 ℃、反应时间3 h、油酸与聚甘油摩尔比4∶1、催化剂用量1.5%,该条件下酯化率为87.7%。采用红外光谱、热重分析、凝胶渗透色谱对产物进行了表征。热重分析表明当温度达到500 ℃时,残留质量为0.21%;凝胶渗透色谱分析结果表明,Mn为2354,Mw为3050,Mz为6549,相对分子质量分布指数为1.2957;拉伸强度为(22.69±3.10)MPa,断裂伸长率为(65.21±5.25)%。

    Abstract:

    The acetylated polyglycerol unsaturated fatty acid esters were prepared using homemade polyglycerol and oleic acid as raw material, which could get the polyglycerol unsaturated fatty acid esters,then reacted with acetic anhydride. The effects of reaction temperature, reaction time, catalyst dosage and mass ratio on the esterification rate were investigated respectively. The optimum process was optimized by single factor experiment research. The highest yield (87.7%) of esterification rate is obtained when reaction temperature is 215 ℃, reaction time is 3 h, the mass ratio of oleic acid and polyglycerol is 4∶1, the catalyst dosage is 1.5% of the raw material. The product was characterized by FT-IR, TG, GPC and application testing. The results of TG show that when the temperature reaches 500 ℃, the residual quality is 0.21%; the distribution of the GPC indexes are 2354 (Mn), 3050 (Mw), 6549 (Mz), 1.2957 (ε) respectively; tensile strength is (22.69±3.10)MPa, the elongation at break is (65.21±5.25)%.

    参考文献
    相似文献
    引证文献
引用本文

胡云, 冯国东, 许彬, 刘朋, 周永红.增塑剂乙酰聚合甘油不饱和脂肪酸多酯的合成及应用[J].高分子材料科学与工程,2015,31(4):31-36. Yun Hu, Guodong Feng, Bin Xu, Peng Liu, Yonghong Zhou. Synthesis and Application of Acetylated Polyglycerol Unsaturated Fatty Acid Esters[J]. Polymer Materials Science & Engineering,2015,31(4):31-36.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-04-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司