化学发泡法制备自结皮聚双环戊二烯泡沫
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河南省杰出人才基金支持(074200510019)


Preparation of Self-Skinning Polydicyclopentadiene Foams by Chemical Blowing Method
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用化学发泡法制备了聚双环戊二烯(PDCPD)泡沫塑料,研究了催化剂比例、模具温度、发泡剂含量等主要因素对泡沫性能的影响。结果表明,模具温度为60~70 ℃,物料摩尔比n(DCPD)/n(WCl6·WOCl4)/n(AlEt2Cl)=1300/1/30左右,发泡剂质量分数不低于0.6%时,得到闭孔结构的自结皮硬质PDCPD泡沫。PDCPD泡沫材料的密度最低可达0.375 g/cm3,比压缩强度可达30.24 MPa/(g·cm-3),结皮硬度为邵氏D65-82度,分解温度可达到450 ℃,具有良好的力学强度和热稳定性。

    Abstract:

    Polydicyclopentadiene (PDCPD) foam can be made by chemical blowing method. The influence of catalysts proportion, mold temperature and content of blowing agent on the properties of PDCPD foams was investigated. The results indicate that when the mold temperature gets 60~70 ℃, the catalysts proportion (n(DCPD/n(WCl6·WOCl4)/n(AlEt2Cl)) is about 1300/1/30 and the content of blowing agent is 0.6% or higher, self-skinning hard PDCPD foams with closed-cell structure were made. The density of PDCPD foams can be as low as 0.375 g/cm3, with the surface hardness at Shore 64-82HD. The decomposition temperature of PDCPD foam gets as high as 450 ℃,showing excellent mechanical properties and thermal stability.

    参考文献
    相似文献
    引证文献
引用本文

陈国伟, 赫玉欣, 李旭阳, 刘秋菊, 张玉清.化学发泡法制备自结皮聚双环戊二烯泡沫[J].高分子材料科学与工程,2015,31(5):149-153. Guowei Chen, Yuxin He, Xuyang Li, Qiuju Liu, Yuqing Zhang. Preparation of Self-Skinning Polydicyclopentadiene Foams by Chemical Blowing Method[J]. Polymer Materials Science & Engineering,2015,31(5):149-153.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-05-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司