亚麻纤维/立构聚乳酸复合材料的制备与性能表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation and Characterization of Flax Fiber Reinforced Polylactide Stereocomplex Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用等比例聚左旋乳酸( PLLA) /聚右旋乳酸( PDLA) 熔融共混和注塑成型制备了立构聚乳酸(sc-PLA)和10%亚麻纤维(Flax)增强的sc-PLA复合材料,通过力学性能测试、差示扫描量热法、扫描电镜、X射线衍射、维卡软化点测试等方法对2种材料的力学性能、结晶性能、断面形貌以及耐热性能进行了比较。结果表明,制得的sc-PLA与10% Flax/sc-PLA复合材料中立构晶体与均聚物晶体并存,亚麻纤维的加入有利于提高材料的结晶度,其sc晶体生成率由66.4%提高到92.7%。与均聚物PLLA相比,sc-PLA的耐热性能虽有所增强,但力学性能还有待提高。加入了10%亚麻之后,复合材料力学性能明显改善,其拉伸强度、拉伸模量以及悬臂梁缺口冲击强度比sc-PLA分别提高了34.1%,49.8%和289.1%。此外,10%Flax/sc-PLA复合材料还具有较好的耐热性能,其维卡软化温度达到了155.6 ℃,比PLLA提高近92 ℃。

    Abstract:

    Polylactide stereocomplex(sc-PLA) prepared by blending equivalent proportion of poly(L-lactic acid) /poly(D-lactic acid) (PLLA/PDLA) and its composites reinforced with 10% flax fibers were fabricated by melting compounding and followed by injection molding. Then the mechanical properties, crystallinity, cross-section morphology, and heat-resistance properties of two materials were studied by the mechanical property test, DSC, SEM, XRD, and Vicat softening point test. The results show that sc-PLA and 10% flax/sc-PLA composite exhibit both homocrystallites and stereocomplex crystallites. The crystallinity degree of composite is increased by reinforcement of flax fibers, and the yield of sc-crystallites of 10% flax/sc-PLA composite could reach 92.7%, higher than that of sc-PLA (66.4%). Compared with homopolymer PLLA, the heat-resistance property of sc-PLA is increased greatly, while its mechanical properties is decreased somewhat. By the addition of 10% flax fibers, the mechanical properties of sc-PLA are improved significantly, the tensile strength, elastic modulus and Izod notched impact strength of 10% flax/sc-PLA composite are increased by 34.1%, 49.8% and 289.1%, respectively. Moreover, 10% flax/sc-PLA composite shows a good heat-resistance property, and its Vicat softening temperature could achieve 155.6 ℃, increased nearly 92 ℃ than that of PLLA.

    参考文献
    相似文献
    引证文献
引用本文

明瑞豪, 杨革生, 李玉增, 张慧慧, 邵惠丽.亚麻纤维/立构聚乳酸复合材料的制备与性能表征[J].高分子材料科学与工程,2015,31(5):169-172. Ruihao Ming, Gesheng Yang, Yuzeng Li, Huihui Zhang, Huili Shao. Preparation and Characterization of Flax Fiber Reinforced Polylactide Stereocomplex Composites[J]. Polymer Materials Science & Engineering,2015,31(5):169-172.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-05-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司