超声外场作用下聚合物注射成型模内流动行为的物理可视化分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51475071);973计划项目(2012CB025905)


Polymer Flowing Behavior Analysis of Ultrasonic Vibration Assisted Injection Molding Based on Physical Visualized Technology
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以3.5 mm矩形平板塑件注射充模过程为研究对象,开发一种用于超声辅助成型技术观测的新型可视化试验分析平台,通过在模具型腔上施加超声振动,研究超声振动对聚丙烯(PP)熔体前沿流动速度以及流动轨迹的影响。结果表明,超声振动能提高PP前沿流动速度(400 W超声时,最高可使前沿流速提高18.0%),充模前期超声振动对提升前沿流速的贡献最大,但是充模中后期,超声振动和剪切热的共同作用决定着前沿流速的大小;同时,超声振动对冷凝区的改变是PP流动轨迹出现分散流动延后变化的主因。

    Abstract:

    In this research, filling process of 3.5 mm retangular plastic injection process was studied. For understanding behavior of polymer melts flows in injection molding with help of ultrasonic vibration, a novel visualization device was developed. By the device and the method, influence of ultrasonic vibration on filling front velocity and velocity distribution of PP melts within cavity were discussed. The results show that the filling front velocity is improved by ultrasonic vibration (filling front velocity is improved by 18.0% at most, under ultrasonic power of 400W). At the early stage of filling process, the contribution of ultrasonic vibration to improvement of melts front flow is the largest. However, during the mid and last filling process, melts front flow velocity is determined by the combination of ultrasonic vibration and shear heat. Besides, the main reason for delay of PP dispersed flow is the vibration of condensing zones caused by ultrasonic vibration.

    参考文献
    相似文献
    引证文献
引用本文

姜开宇, 吉智, 李豪, 王敏杰, 于同敏.超声外场作用下聚合物注射成型模内流动行为的物理可视化分析[J].高分子材料科学与工程,2015,31(7):101-106. Kaiyu Jiang, Zhi Ji, Hao Li, Minjie Wang, Tongmin Yu. Polymer Flowing Behavior Analysis of Ultrasonic Vibration Assisted Injection Molding Based on Physical Visualized Technology[J]. Polymer Materials Science & Engineering,2015,31(7):101-106.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-07-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司