同向非对称双螺杆挤出HDPE/PS共混体系沿程混合表征
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(11272093);广东省高等职业院校珠江学者岗位计划资助项目(2012);广东省部产学研项目(2012B091100432);广东省教育厅项目(2013CXZDB004);广东轻院自然科学基金项目(KJ201212)


Characterization of Mixing of HDPE/PS Blend in Co-Rotating Non-Twin Screws Extruder Along Extrusion Direction
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    同向非对称双螺杆挤出机作为新型加工设备,混合机理以及聚合物相形态变化是值得关注的重点。文中借助HDPE/PS共混体系,对同向非对称双螺杆挤出机螺槽充满程度以及螺杆输送机理做出简要分析,对挤出过程沿程混合相形态及分散相粒径统计分析表征。结果表明,同向非对称双螺杆挤出机中双头螺槽填充率高于单头,物料完全熔融后,粒径变化较小,而在同一径向长度,单头螺槽内分散相粒径略小于双头螺槽,并对这一现象进行了初步分析。

    Abstract:

    The co-rotating non-twin screws extruder was a new type of extruder in which the asymmetrical effect was introduced into the screw channel to enhance mixing. The mixing mechanism and the change in polymer phase morphology were worth focusing on. The HDPE/PS blends were used to examine the fill degree and the screw conveying mechanisms in this new type of screw grooves, and then the phase morphology along extrusion process as well as the particle size distributions of dispersed phase was characterized. The experimental results show that the fill degree in the two-tips screw is larger than that in the one tip screw. The variation of the particle size is not significant after melting. However, at the same radial direction, the particle size of the dispersed phase in the one tip screw grooves is smaller than that in the two-tip screw, the reasons for this phenomenon were analyzed.

    参考文献
    相似文献
    引证文献
引用本文

喻慧文, 罗家胜, 徐百平, 何亮, 王玫瑰, 杜遥雪.同向非对称双螺杆挤出HDPE/PS共混体系沿程混合表征[J].高分子材料科学与工程,2015,31(8):113-117. Huiwen Yu, Jiasheng Luo, Baiping Xu, Liang He, Meigui Wang, Yaoxue Du. Characterization of Mixing of HDPE/PS Blend in Co-Rotating Non-Twin Screws Extruder Along Extrusion Direction[J]. Polymer Materials Science & Engineering,2015,31(8):113-117.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-12-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司