无水AlCl3催化苯乙烯-丙烯腈共聚物/三元乙丙橡胶就地相容化
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省产学研基金资助项目(BY2013024--08)


In-Situ Compatiblization of SAN/EPDM Blends Catalyzed by Anhydrous Aluminium
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用扭矩分析、凝胶含量和力学性能测定、共混物热分析、界面形态观察等方法考察了无水AlCl3催化剂用量对苯乙烯-丙烯腈共聚物(SAN)和三元乙丙橡胶(EPDM)大分子间Friedel-Crafts烷基化反应的影响,并与不同量过氧化物催化进行比较。结果表明,在m(SAN)/m(EPDM)为60.0∶40.0共混物中加入0.4%无水AlCl3有利于生成较多的EPDM-g-SAN接枝共聚物,SAN接枝率为2.1%,与简单共混物相比,增容体系力学性能得到明显提高,拉伸强度从17.5 MPa提高至23.5 MPa,断裂伸长率从2.1%提高至6.7%;进一步提高AlCl3用量,SAN中侧链氰基和铝离子络合作用增强,导致共混物的MFR、SAN接枝率、力学性能下降,SAN玻璃化转变温度提高;SAN相对分子质量随着AlCl3用量增加略有下降。以无水AlCl3为催化剂,SAN接枝率及共混物力学性能明显优于过氧化物催化剂。

    Abstract:

    Using torque analysis, determination of gel content and mechanical properties, thermal analysis, the interface morphology observation and other methods, effects of the amount of anhydrous aluminum chloride(AlCl3) on Friedel-Crafts alkylation reaction between poly(ethylene-propylene-diene monomer)(EPDM) andstyrene-acrylonitrile copolymer(SAN) were investigated. The results show that adding 0.4% AlCl3 to m(SAN)/m(EPDM)(60.0∶40.0) blends helps to produce more EPDM-g-SAN copolymer, and the grafting-ratio of SAN is 2.1%. The mechanical properties of the compatibilized blends are improved notably compared to those of the mechanical blends, for example, the tensile strength is increased from 17.5 MPa to 23.5 MPa and its elongation at break is increased from 2.1% to 6.7%. If the dosage of AlCl3 is increased further, the complexing abilities between the cyanogroup of side chains of SAN and aluminum cations are enhanced, and result in decreasing of MFRs, mechanical properties of the SAN/EPDM blends and grafting-ratios of SAN, increasing of the glass transition temperatures of SAN. The molecule weight of SAN in the blends declines very slightly when the dosage of AlCl3 is increased further. With anhydrous aluminum chloride(AlCl3) as catalyst, the SAN grafting-ratio and mechanical properties of SAN/EPDM blends are obviously better than using the peroxide catalyst.

    参考文献
    相似文献
    引证文献
引用本文

徐建平, 董银春, 郜志刚, 龚方红, 刘春林.无水AlCl3催化苯乙烯-丙烯腈共聚物/三元乙丙橡胶就地相容化[J].高分子材料科学与工程,2015,31(8):123-127. Jianping Xu, Yanchun Dong, Zhigang Gao, Fanghong Gong, Chunling Liu. In-Situ Compatiblization of SAN/EPDM Blends Catalyzed by Anhydrous Aluminium[J]. Polymer Materials Science & Engineering,2015,31(8):123-127.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-12-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司