长支化聚丙烯结晶性对低温釜式发泡行为的影响
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

上海市自然科学基金资助项目(13ZR1411400);中央高校基本科研业务费专项资金资助(222201313012)


Effects of Crystal Status on the Solid-State Foaming Process of Long Chain Branched Polypropylene
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以自制的长支化聚丙烯(LCB PP)为原料,进行不同热历史处理,研究了LCB PP结晶状态与低温固相发泡行为之间的关系。由于自制的LCB PP带有较多的支化结构,在结晶过程中可以起到异相成核的作用,因此在较高降温速率下,可以制得微晶尺寸较小,晶区不完善的LCB PP。结果表明,结晶度、晶区完善程度和微晶尺寸对自制LCB PP熔点以下的低温固相发泡行为有着显著影响,三者之间存在协同作用:随LCB PP结晶度降低,晶区不完善度增加,微晶尺寸减小,CO2在LCB PP基体中的溶解度和扩散系数显著提高,且LCB PP发泡后的泡孔结构明显改善;同时,低结晶度、小微晶尺寸,晶区完善度较低的LCB PP在固相发泡时有更宽的可发泡温度区间和更高的发泡倍率。

    Abstract:

    Three kinds of self-made long chains branching polypropylene (LCB PP) samples with different crystal statuses were prepared by different thermo-history. The influence of crystal status on the solid-state foaming process of the LCB PP was investigated. Smaller crystal size and higher crystal defect could be obtained by cooling at the fast rate and the abundant LCBs in the LCB PP sample may act as heterogeneous nucleation during crystallization. The results indicate that the solid-state forming process of the LCB PP is closely related to its crystallinity, crystal defect, and micro-crystal size. The solubility and diffusion coefficient of CO2 into LCB PP obviously increase with decrease of the crystallinity and micro-crystal size, and increase of the crystal defect. Therefore, the cellular structure of the foamed PP is optimized. Furthermore, a widened foaming temperature zone and a high foaming expansion ratio could be achieved for the LCB PP with lower crystallinity, smaller micro-crystal size and higher crystal defect.

    参考文献
    相似文献
    引证文献
引用本文

胡渠敦, 李军, 郑安呐, 管涌, 李书召.长支化聚丙烯结晶性对低温釜式发泡行为的影响[J].高分子材料科学与工程,2015,31(8):133-138. Qudun Hu, Jun Li, Anna Zheng, Yong Guan, Shuzhao Li. Effects of Crystal Status on the Solid-State Foaming Process of Long Chain Branched Polypropylene[J]. Polymer Materials Science & Engineering,2015,31(8):133-138.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-12-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司