反应型磷氮复合阻燃多元醇制备聚氨酯阻燃硬泡及性能
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(21274049);中央高校基本科研业务费专项资金资助


Preparation and Properties of Reactive Flame-Retarded Polyurethane Rigid Foam with Phosphorus- and Nitrogen-Containing Polyol
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用磷氮复合阻燃多元醇与通用聚醚配合制备阻燃聚氨酯硬泡,泡沫的尺寸稳定性均在1%左右,导热系数在0.03 W/(m·K)以下。压缩强度结果表明阻燃泡沫能满足一般建筑用聚氨酯硬泡保温材料的使用要求,动态力学测试表明泡沫的Tg随着阻燃聚醚用量的增加而升高,热失重测试表明硬泡的残炭量也随阻燃聚醚的增加而升高,阻燃多元醇制备的硬泡极限氧指数达到24.8%,较未做阻燃处理的泡沫有明显提高。

    Abstract:

    A phosphorus- and nitrogen-containing polyether polyol resulting from tetrakis(hydroxymethyl)phosphonium sulfate(THPS)was utilized as reactive fire-retardant to prepare the polyurethane rigid foam(PUR). Experimental results show that the newly made tris((N,N-bis(hydroxyethyl)aminomethyl)phosphine oxide (THAPO) can accelerate the foaming speed, and result in a high dimensional stability and low thermal conductivity (less than 0.03 W/(m·K)) rigid foam. Compressive stress testing indicates that rigid foams are strong enough to meet commercial standard. In addition, DMA and TGA test suggest that the glass transition temperature (Tg), char yield (CR) and limited oxygen index (LOI) increase with the addition of THAPO and the highest LOI value reaches 24.8%.

    参考文献
    相似文献
    引证文献
引用本文

张汪强, 郭刚, 邱进俊, 刘承美.反应型磷氮复合阻燃多元醇制备聚氨酯阻燃硬泡及性能[J].高分子材料科学与工程,2015,31(9):141-146. Wangqiang Zhang, Gang Guo, Jinjun Qiu, Chengmei Liu. Preparation and Properties of Reactive Flame-Retarded Polyurethane Rigid Foam with Phosphorus- and Nitrogen-Containing Polyol[J]. Polymer Materials Science & Engineering,2015,31(9):141-146.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-09-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司