缝合泡沫夹芯结构复合材料VARTM工艺树脂充填模拟及验证
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51263015,51265012);江西省自然科学基金资助项目 (20122BAB206011);人社厅留学人员择优项目(赣人社字[2012]375号)


Process Simulation and Verification of Stitched Foam Core Sandwich Structure by VARTM Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用“长条”模型代替泡沫中沿缝线方向树脂流动模型并对其等效渗透率及孔隙率进行计算;然后用PAM-RTM软件对缝合泡沫夹芯结构真空辅助树脂传递模塑成型(VARTM)工艺树脂充填过程进行数值模拟,最后建立了流动可视化实验装置对模拟结果进行实验验证。对比模拟与实验结果表明,模拟与实验完成整个充填过程的时间非常接近,并且树脂在预成型体中流动方式及在预成型体上、下面板流动状态的数值模拟与实验结果也非常地一致。故建立的“长条”模型及其相关参数的计算是合理的,可以用来准确地预测缝合泡沫夹芯结构VARTM工艺树脂充填过程。另外,树脂在上面板流动前沿在沿宽度方向较为统一,而树脂在下面板流动前沿呈现锯齿状,容易产生空隙及干斑等缺陷,影响制品的质量。

    Abstract:

    A“strip”model was proposed to replace the model of resin flow along the stitching direction in foam and its equivalence permeability and porosity were calculated. Then the resin flow in stitched foam core sandwich preform during vacuum assisted resin transfer molding (VARTM)process was simulated by PAM-RTM and a visual flow experimental device was established to verify the simulation results. The results of experiment and simulation show that the overall infiltration time of simulation and experiment were very close; the pattern of resin infiltrate in the perform and the conditions of resin flow on top face sheet and bottom face sheet were quite uniform. As a conclusion, the establishment of the “strip”model and the calculation of its relevant parameters are quite reasonable, they can be used to predict the resin infiltrate in the stitched foam core sandwich structure during VARTM process accurately.In addition,flow front of resin in the top face sheet is uniform along the width direction, however, flow front of resin in the bottom face sheet presents a saw tooth shape, this can results voids and dry spots easily, and then affects the quality of the product.

    参考文献
    相似文献
    引证文献
引用本文

王科, 赖家美, 鄢冬冬, 黄志超, 柳和生.缝合泡沫夹芯结构复合材料VARTM工艺树脂充填模拟及验证[J].高分子材料科学与工程,2015,31(11):124-129. Ke Wang, Jiamei Lai, Dongdong Yan, Zhichao Huang, Hesheng Liu. Process Simulation and Verification of Stitched Foam Core Sandwich Structure by VARTM Process[J]. Polymer Materials Science & Engineering,2015,31(11):124-129.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-11-18
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司