羧基功能化聚芳醚酮的合成及电纺性
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河北省高等学校科学研究项目(QN2014051);河北联合大学大学生创新项目(X2014072)


Synthesis and Electrospinning of Carboxyl-Functionalized Poly(Aryl Ether Ketone)
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以4,4-二(4-羟基苯基)戊酸(PDA)、酚酞(PHT)和4,4-二氟二苯甲酮(DFK)为原料,调节PDA和PHT的比例,采用亲核取代路线,制备了一系列羧基功能化聚芳醚酮(PAEK-C)。通过核磁共振氢谱和红外光谱确定了聚合物的化学结构,广角X射线衍射数据表明共聚物系无定形聚合物,差示扫描量热分析和热重分析表明聚合物存在单一的玻璃化转变温度(Tg>210 ℃),玻璃化转变温度和热失重5%的温度随PDA含量的增加而降低。通过高压静电纺丝技术制备了PAEK-C超细纤维膜。结果表明,使用N,N-二甲基乙酰胺(DMAc)/四氢呋喃(THF)混合溶剂,可以制备出较均匀的纤维,纤维直径随THF比例增加而减小,扫描电镜图像显示,超细纤维膜的纤维直径在200~350 nm。

    Abstract:

    A series of carboxyl-functionalized poly(aryl ether ketone)s (PAEK-C) were synthesized via aromatic nucleophilic substitution copolycondensation of 4,4′-bis(4-hydroxyphenyl)pentanoic acid(PDA), phenolphthalein (PHT) and 4,4′-difluoro diphenylmethanone. The chemical structures of the synthesized polymers were characterized by FT-IR and 1H-NMR. From the X-ray diffraction (XRD) data, these polymers could be observed to have amorphous structure. Furthermore, according to the DSC and TGA tests, it could be seen that PAEK-Cs have a single glass transition temperature(Tg>210 ℃), and the Tg and onset temperature of 5% mass loss (Td5%) decrease with PDA content increasing. The ultra fine fiber membranes of PAEK-C with the diameter of 200~350 nm were prepared by electrospinning in the mixed solvent of N,N-dimethyl acetamide(DMAc) and tetrahydrofuran(THF). The diameter of fiber could be decreased by increasing the THF content in the mixed solvent.

    参考文献
    相似文献
    引证文献
引用本文

虞聪, 桑冀蒙, 李玉青, 李婷婷, 闫莉, 张志明.羧基功能化聚芳醚酮的合成及电纺性[J].高分子材料科学与工程,2015,31(12):16-20. Cong Yu, Jimeng Sang, Yuqing Li, Tingting Li, Li Yan, Zhiming Zhang. Synthesis and Electrospinning of Carboxyl-Functionalized Poly(Aryl Ether Ketone)[J]. Polymer Materials Science & Engineering,2015,31(12):16-20.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-12-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司