微孔塑料挤出发泡数值模拟
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51463015)


Numerical Simulation of Microcellular Plastics Extrusion Foaming
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    微孔塑料连续挤出发泡中的熔体压力和压力降速率是比较重要的参数,一般而言越大的压力降和压力降速率越有利于微孔连续挤出发泡成型。文章通过对毛细管口模的模拟,总结了几种提高熔体压力和压力降速率的方法,分析了熔体温度和熔体中CO2的溶解度对熔体流动的影响。研究发现,可以通过缩小毛细管直径、增加毛细管长度、降低熔体温度、降低熔体中的CO2溶解含量、增加质量流率来提高熔体压力;可以通过缩小口模直径,降低熔体温度、降低CO2溶解含量、增加质量流率来增加熔体的压力降速率。

    Abstract:

    Melt pressure and pressure drop rate are important parameters in microcellular plastics continuous extrusion foaming. Generally, greater pressure drop and pressure drop rate are conducive to microcellular plastics continuous extrusion foaming. In this paper, capillary die was simulated, some ways to increase melt pressure and pressure drop rate were summarized, the influence of melt temperature and solubility of CO2 in melt to melt flow was analyzed. The results show that reduced capillary diameter, increased capillary length, lower melt temperature, lower solubility of CO2 in melt can increase melt pressure; reduced capillary diameter, lower melt temperature and lower solubility of CO2 in melt can increase pressure drop rate.

    参考文献
    相似文献
    引证文献
引用本文

熊鹏, 黄兴元, 柳和生, 李孟山.微孔塑料挤出发泡数值模拟[J].高分子材料科学与工程,2015,31(12):104-107. Peng Xiong, Xingyuan Huang, Hesheng Liu, Mengshan Li. Numerical Simulation of Microcellular Plastics Extrusion Foaming[J]. Polymer Materials Science & Engineering,2015,31(12):104-107.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2015-12-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司