聚合物熔体环绕型芯充型流动行为的物理可视化分析
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51475071);973项目(2012CB025905)


Visualization Analysis on Polymer Filling Behavior of Injection Molding of RingShaped Workpieces
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    利用自行开发的超声振动辅助注射成型可视化实验装置,对不同注射速度下聚丙烯(PP)在环形型腔内环绕型芯充型流动特性进行可视化试验,观测分析不同注射速度对熔体充型流动行为的影响。分析结果表明,不同注射速度对环形制件注塑成型充型流动行为产生不同程度的影响,在较低注射速度时,型腔内的气体压力变化平稳,熔体流动速度比较平稳无明显变化;在较高注射速度时,在充填过程中型腔内的气体压力急剧变化,熔体速度出现波动且在流动后期熔体的流动速度出现骤降,注射速度对熔体流动前沿的面积变化也有直接影响。在高速注射时,型腔内气体压力的变化是影响熔体充型流动特性的主因;在低速注射时,熔体与型腔表面的热交换是影响熔体充型流动特性的主因。

    Abstract:

    To have better understanding of the influence of injection speed on injecting molding characteristics of melt in the groove mould cavity, effects of the different injection speed on flowing behaviors of PP melt in the groove mould cavity were observed by selfdeveloped injection molding experimental device and highspeed video camera. The results show that the effects of different injection speed on injection molding behaviors of PP melt in ring groove cavity were unlike. Under low injection speed, with the gas pressure changing and increasing in cavity slowly and steadily, the melt filling velocity does not change obviously during injection process; while under the high injection speed, as the gas pressure in the cavity changes and increases rapidly, the melt filling velocity changes and decreases fast at the later filling period under the effects of gas pressure during injection process. The flow front area is affected by the injection speed as well. In the case of the high injection speed, the effect of gas pressure on melt becomes the main cause which influences the flowing behaviors. In case of the low injection speed, the main reason which influences the flowing behaviors is effects of melt temperature decrease caused by the heat exchange between melt and cavity surface.

    参考文献
    相似文献
    引证文献
引用本文

姜开宇, 左军超, 杨磊, 王龙飞, 王敏杰.聚合物熔体环绕型芯充型流动行为的物理可视化分析[J].高分子材料科学与工程,2016,32(1):120-124. Kaiyu Jiang, Junchao Zuo, Lei Yang, Longfei Wang, Minjie Wang. Visualization Analysis on Polymer Filling Behavior of Injection Molding of RingShaped Workpieces[J]. Polymer Materials Science & Engineering,2016,32(1):120-124.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司