静电喷涂制备超高分子量聚乙烯锂电池复合隔膜
DOI:
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation of UHMWPE Lithium Battery Composite Separator by Electrospraying
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    通过静电喷涂技术成功制备出一种超高分子量聚乙烯(UHMWPE)锂电池复合隔膜。首先通过研究溶液浓度及电压等因素对聚偏氟乙烯(PVDF)溶液静电喷涂的影响,确定最佳喷涂条件为PVDF质量分数3%,喷涂电压21 kV。然后通过在超高分子量聚乙烯隔膜上静电喷涂PVDF颗粒,制备出复合隔膜。最后,对该复合隔膜的孔隙率、热稳定性、充放电性能测试。结果表明,该隔膜的孔隙率从46.5%提高到73.1%;纵向热收缩率从2.6%降低到1.3%;首次放电容量比相应的超高分子量聚乙烯隔膜提高了4.2%,经过50次循环,稳定性良好,可作为锂离子电池隔膜使用。

    Abstract:

    In this paper, an ultra high molecular weight polyethylene (UHMWPE) lithium ion battery composite separator was successfully prepared via electrospraying technique. The optimal electrospraying parameters of polyvinylidene fluoride (PVDF), mass fraction of PVDF 3%, electrospraying voltage 21 kV, were successfully determined by adjusting the voltage value and concentration of PVDF solution. The composite separator was prepared by electrospraying PVDF particles on the UHMWPE separator. The porosity rate, thermal stability and charge and discharge properties were analyzed. The analytical results show that the porosity rate of the composite separator is increased from 46.5% to 73.1%, and the heat shrinkage of the separator in the longitudinal is reduced from 2.6% to 1.3%. The first specific discharge capacity of the composite separator is increased by 4.2%, and the separator has good cycle stability after 50 cycles, which could be used as lithium ion battery separator.

    参考文献
    相似文献
    引证文献
引用本文

赵云腾, 刘太奇.静电喷涂制备超高分子量聚乙烯锂电池复合隔膜[J].高分子材料科学与工程,2016,32(1):147-150. Yunteng Zhao, Taiqi Liu. Preparation of UHMWPE Lithium Battery Composite Separator by Electrospraying[J]. Polymer Materials Science & Engineering,2016,32(1):147-150.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司