碳酸钙填充对PVC增塑糊黏度的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

白科合同[2014]29号;国家科技支撑计划(2007BAE10B03)


Viscosity and Aging Process of CaCO3 Filled Polyvinyl Chloride Plastisols
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    文章研究了碳酸钙(CaCO3)未填充和填充情况下,3种不同生产方法、相近聚合度的聚氯乙烯(PVC)糊树脂在对苯二甲酸二辛脂(DOTP)和乙酰柠檬酸三正丁酯(ATBC)2种增塑体系中的黏度性能,以及黏度性能与增塑糊中粒子颗粒形态关系。结果表明,无论CaCO3填充与否,增塑糊黏度在DOTP体系下均比ATBC的大,主要与增塑剂分子结构有关;未填充CaCO3时,增塑糊黏度性能主要受PVC糊树脂和增塑剂间相容性的影响,3种糊树脂与DOTP的相容性均比ATBC的好;填充CaCO3后,几种增塑糊黏度均增大,黏度性能主要受相容性和树脂与CaCO3粒子颗粒形貌的共同影响。

    Abstract:

    The viscosity and its aging process of unfilled and calcium carbonate (CaCO3) filled polyvinyl chloride (PVC) plastisols were investigated comparatively by vibrational viscometry, and the morphology of the PVC resins employed and of the plastisols prepared was observed by scanning electron microscopy. The results indicate that the viscosity of the dioctyl terephthalate based plastisols is higher than that of the acetyl tributyl citrate based plastisols, no matter whether the CaCO3 filled or not. It is mainly on account of the different molecular structures between the two plasticizers. Moreover, the viscosity of unfilled plastisols is mainly determined by the compatibility between plasticizer and PVC particles, but the viscosity of filled plastisols is determined by the compatibility and particle morphology simultaneously.

    参考文献
    相似文献
    引证文献
引用本文

吉玉碧, 徐国敏, 杨照, 罗恒, 谭红.碳酸钙填充对PVC增塑糊黏度的影响[J].高分子材料科学与工程,2016,32(2):54-59. Yubi Ji, Guomin Xu, Zhao Yang, Heng Luo, Hong Tan. Viscosity and Aging Process of CaCO3 Filled Polyvinyl Chloride Plastisols[J]. Polymer Materials Science & Engineering,2016,32(2):54-59.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-26
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司