三相存在下聚丙烯/纤维复合发泡材料的力学性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(21264004);黔科合重大专项字(2012)6023;黔科合人才团队[2014]4006


Mechanical Properties of Polypropylene/Fiber Composite Foaming Materials Under the Condition of Three-Phase Existing
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用密炼方式分别制备碳纤维(CF)、玻璃纤维(GF)、芳纶纤维(AF)增强聚丙烯(PP)母粒,通过注塑成型制备相应的聚丙烯/纤维复合发泡材料,研究了3种纤维对微发泡聚丙烯/纤维复合发泡材料力学性能的影响。结果表明,PP/CF复合发泡材料的综合性能提高的幅度最大,其中拉伸、压缩、弯曲强度分别提高了100.9%,80.4%,126.5%;PP/AF复合发泡材料的韧性最好,相对于纯PP提高了151.2%;并且,PP/CF复合发泡材料的泡孔参数最好,泡孔尺寸为28.97 μm,泡孔密度为8.58×106 cm-3,泡孔尺寸分布达到9.22 μm。

    Abstract:

    Polypropylene(PP) reinforced composites with three different fibers, such as carbon fiber(CF), glass fiber(GF), aramid fibers(AF), were prepared by banburying and then foamed by injection molding method. The effects of different fibers on mechanical properties of microcellular foams were investigated. The results indicate that PP/CF shows the best comprehensive mechanical properties among three fiber reinforced foams, whereas PP/AF exhibits the best toughness. Compared with PP microcellular foams, the tensile, compressive, and flexural strength of the PP/CF increase by 100.9%, 80.4%, and 126.5%, respectively while the toughness of PP/AF increases by 151.2%. In addition, the cell diameter, cell density, and cell size distribution of PP/CF composite are 28.97 μm, 8.58×106 cm-3, and 9.22 μm, respectively, which exhibit the best cell structure parameter among fiber reinforced foams.

    参考文献
    相似文献
    引证文献
引用本文

段焕德, 王昌银, 王醴均, 蒋团辉, 何力, 龚维.三相存在下聚丙烯/纤维复合发泡材料的力学性能[J].高分子材料科学与工程,2016,32(2):71-77. Huande Duan, Changyin Wang, Lijun Wang, Tuanhui Jiang, Li He, Wei Gong. Mechanical Properties of Polypropylene/Fiber Composite Foaming Materials Under the Condition of Three-Phase Existing[J]. Polymer Materials Science & Engineering,2016,32(2):71-77.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-26
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司