MQ树脂增强硅橡胶及其透紫外影响因素分析
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

绿色轻工材料湖北省重点实验室开放基金(2013CLZD04)


MQ Resin Reinforced Silicone Rubber and Analysis of Influencing Factors of Ultraviolet-Transparent
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    利用硅氢加成反应原理在铂金催化剂作用下和高温固化环境中制备了加成型液体硅橡胶,并通过乙烯基MQ树脂对硅橡胶进行强度改性;采用材料蠕变试验机、差示扫描量热仪对硅橡胶力学性能、热学性能进行研究,并对硅橡胶透紫外影响因素进行分析。实验结果表明,乙烯基MQ树脂可在硅橡胶中产生“集中交联”效应,随着乙烯基MQ树脂含量的增加,固化后硅橡胶的拉伸强度随之增加,而紫外透过率从整体上表现出先降低后增加的趋势。当乙烯基MQ树脂质量分数为80%时,高透紫外加成型液体硅橡胶具有良好的综合性能(拉伸强度5.57 MPa,断裂伸长率265.34%,350 nm下的透过率90.5%)。

    Abstract:

    Ultraviolet-transparent addition type liquid silicone rubber was prepared by heat curing method and modified by using vinyl MQ resin as reinforcing agent. Curing process, mechanical property and UV transmittance of modified silicone rubber were investigated by differential scanning calorimeter, electronic creep testing machine and ultraviolet and visible spectrophotometer. The influence factor of UV transmittance was also analysised. The experimental result show that vinyl-MQ resin can form effects of concentrative crosslinking and inhibiting on curing of silicone rubber. The tensile stength of silicone rubber increases as the loading of vinyl-MQ resin goes up. While the UV-transmittance of silicone rubber presents the different tendency in its entirety that it decreases in the innital content range of vinyl-MQ resin, then increases in the hight content range. In conclusion, silicone rubbers have a good integrate property (tensile strength of 5.57 MPa, elongation at break of 265.34%, UV-transmittance at 350 nm of 90.5%), when the mass fraction of vinyl-MQ resin is 80% in the silicone rubber.

    参考文献
    相似文献
    引证文献
引用本文

吕志勇, 李静, 孙筱萌, 尹应乐, 覃虎川, 陈绪煌. MQ树脂增强硅橡胶及其透紫外影响因素分析[J].高分子材料科学与工程,2016,32(2):90-94. Zhiyong Lü, Jing Li, Xiaomeng Sun, Yingle Yin, Huchuan Qin, Xuhuang Chen. MQ Resin Reinforced Silicone Rubber and Analysis of Influencing Factors of Ultraviolet-Transparent[J]. Polymer Materials Science & Engineering,2016,32(2):90-94.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-26
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司