等规聚丙烯微注塑制品的形态结构和力学性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(11372287); 博士点基金(20124101110007)


Morphology, Microstructure and Mechanical Properties of Micro Injection Molded Isotactic Polypropylene Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    选用等规聚丙烯材料,基于正交表L25(56)进行微注塑成型实验,制备厚度为0.5 mm的微注塑拉伸试样。采用偏光显微镜和广角X射线衍射仪对其形态结构进行表征,并分析工艺参数对微制品形态结构的影响规律和影响度。对微制品试样进行拉伸实验,分析工艺参数对其屈服应力、弹性模量和断裂伸长率的影响规律和重要度。结果表明,注射速度对微试样的形态结构和力学性能的影响最大;皮层厚度和皮层取向度随着注射速度的增大而减小;屈服应力随注射速度、熔体温度的增大而减小;熔体温度对弹性模量和断裂伸长率的影响较大,且弹性模量随着熔体温度的升高而减小,断裂伸长率随着熔体温度的升高而增大。

    Abstract:

    Isotactic polypropylene was used as experimental material. The micro-injection molded experiments were conducted to mold the parts with the thickness of 0.5 mm based on the orthogonal array L25(56). The morphology and micro structure were characterized by polarizing microscope and wide-angle X-ray diffraction, and the effect and significance of process parameters on the morphology and microstructure of micro-injection molded parts were analyzed. The tensile tests were conducted to analyze the effect and the significance of process parameters on yield stress, modulus and elongation at break. The results show that the injection speed has the largest influence on both the morphology and mechanical property. The thickness and the orientation degree of the skin layer decreases with the injection speed increasing. The yield stress decreases with the melt temperature and injection speed increasing. Melt temperature has bigger influence on modulus and elongation at break. With the increase of melt temperature, the modulus decreases and the elongation at break increases.

    参考文献
    相似文献
    引证文献
引用本文

张杨, 王利霞, 卞宁, 王东方, 王永贞, 李倩, 申长雨.等规聚丙烯微注塑制品的形态结构和力学性能[J].高分子材料科学与工程,2016,32(2):114-120. Yang Zhang, Lixia Wang, Ning Bian, Dongfang Wang, Yongzhen Wang, Qian Li, Changyu Shen. Morphology, Microstructure and Mechanical Properties of Micro Injection Molded Isotactic Polypropylene Parts[J]. Polymer Materials Science & Engineering,2016,32(2):114-120.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-26
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司