缝合参数对缝合泡沫夹芯结构复合材料VARTM工艺树脂充模的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51263015,51265012);人社厅留学人员择优项目(赣人社字[2012]375号);江西省教育厅资助项目 (GJJ13071)


Effects of Stitching Parameters on Stitched Foam Sandwich Structure Composites Resin Filling by VARTM Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    对不同缝合参数的缝合泡沫夹芯结构复合材料真空辅助树脂传递模塑成型(VARTM)工艺进行数值模拟,研究了针距、行距、缝针直径、芯板厚度及纤维面板厚度等缝合参数对缝合泡沫夹芯结构复合材料VARTM工艺树脂流动充填的影响。结果表明,改变缝合行距对树脂的流动充填速度影响不大,缝合行距越大,树脂在下层纤维面板流动的同步性越差,制品出现空隙及干斑的可能性越大;缝合针距越小,树脂完成充填的时间越长;分别增加缝针直径和泡沫芯板的厚度,树脂完成充填时间呈线性增长,缝针直径越大,下层纤维面板树脂浸润效果越好;纤维面板厚度增加,树脂完成充填的时间变长,且相对于其他缝合参数,纤维面板厚度对树脂流动充填时间影响最大;缝合针距、泡沫芯板的厚度及纤维面板的厚度都不影响树脂在下层纤维面板的浸润效果。

    Abstract:

    The vacuum assisted resin transfer molding (VARTM)process of stitched foam sandwich structure composites with different kinds of stitching parameters were simulated to research effects of suture pitches, spacing, needle diameters, foam core thickness and fiber panel thickness on resin filling. The results show that the filling velocity of resin basically does not change with different row spacing,but the larger spacing is, the worse the synchronization of resin fill in bottom face sheet is, and the voids and dry spots may appear on productions easily; filling time increases with decreasing pitches; filling time increases linearly with increasing needle diameters and foam core thickness respectively, the bigger needle diameter is, the better the resin fills in bottom face sheet; filling time increases with increasing fiber panel thickness, filling time is mostly affected by the thickness of fiber panel compared to other stitching parameters;suture pitches, thickness of foam core and thickness of fiber panel don’t change infiltration results of resin in bottom face sheet.

    参考文献
    相似文献
    引证文献
引用本文

王科, 赖家美, 鄢冬冬, 柳和生, 黄志超.缝合参数对缝合泡沫夹芯结构复合材料VARTM工艺树脂充模的影响[J].高分子材料科学与工程,2016,32(2):137-143. Ke Wang, Jiamei Lai, Dongdong Yan, Hesheng Liu, Zhichao Huang. Effects of Stitching Parameters on Stitched Foam Sandwich Structure Composites Resin Filling by VARTM Process[J]. Polymer Materials Science & Engineering,2016,32(2):137-143.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-26
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司