铸型尼龙/高密度聚乙烯改性氧化石墨烯复合材料的制备与性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河北省应用基础研究计划重点基础研究项目(14961210D);河北省高等学校科学技术研究项目(ZD20131071, Z2014171)


Preparation and Properties of Monomer Casting Nylon/Graphene Oxide Modified with High Density Polyethylene Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    首先通过静电作用将氧化石墨烯(GO)与2, 3-环氧丙基三甲基氯化铵(GTMAC)结合,在氧化石墨烯的表面引入环氧基,再与马来酸酐接枝高密度聚乙烯(HDPE-g-MAH)反应,制得高密度聚乙烯接枝氧化石墨烯(GO-g-HDPE)。采用傅里叶变换红外光谱、X射线衍射及热重分析对接枝产物进行了表征。将GO-g-HDPE作为铸型尼龙(MC尼龙)的填充剂,通过阴离子原位聚合的方法制备了铸型尼龙/GO-g-HDPE复合材料。力学性能测试结果表明,GO-g-HDPE作为MC尼龙的改性材料起到了增强增韧的双重作用,HDPE-g-MAH的质量分数为0.02%时,拉伸强度增加了14.7%,断裂伸长率增加了21.0%,冲击强度增加了30.0%,压缩强度增加了27.2%。同时,MC尼龙吸水率降低,热稳定性增加。

    Abstract:

    Graphene oxide (GO) was modified with glycidyl trimethyl ammonium chloride (GTMAC) by electrostatic interaction, to introduce the epoxy group on the surface of GO. The high density polyethylene grafted GO (GO-g-HDPE) was prepared via a ring opening reaction between high density polyethylene grafted maleic anhydride (HDPE-g-MAH) and the modified GO by a solution process. Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) were used to characterize the grafted GO. Monomer casting nylon (MC nylon)/GO-g-HDPE composite was prepared by anionic in situ polymerization. The resulting MC nylon composite with 0.02% of GO-g-HDPE demonstrates that the tensile strength, elongation at break, impact strength and compressive strength of the composite are enhanced by 14.7%, 21.0%, 30.0% and 27.2%, respectively, meanwhile, the water absorption and thermal stability are also improved.

    参考文献
    相似文献
    引证文献
引用本文

王月欣, 刘圣贤, 张倩, 孟清.铸型尼龙/高密度聚乙烯改性氧化石墨烯复合材料的制备与性能[J].高分子材料科学与工程,2016,32(2):164-167. Yuexin Wang, Shengxian Liu, Qian Zhang, Qing Meng. Preparation and Properties of Monomer Casting Nylon/Graphene Oxide Modified with High Density Polyethylene Composites[J]. Polymer Materials Science & Engineering,2016,32(2):164-167.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-01-26
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司