超声粉末模压成型超高分子量聚乙烯微塑件的相结构演变规律
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51405306,51501116);深圳市基础研究计划资助项目(JCYJ20150525092941026,JCYJ20140418095735629)


Phase Structure Development of Micro-UPM UHMWPE Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以带有微孔阵列(直径为150 μm)的印制电路板(PCB)为微型腔镶块,将此微镶块应用于超声粉末模压成型工艺(micro-UPM),按照设定的成型工艺参数成型出超高分子量聚乙烯(UHMWPE)微圆柱阵列塑件。差示扫描量热分析和纳米压痕实验数据表明,UHMWPE粉末未预热时所成型出的微圆柱阵列塑件整体上由初生态和熔化再结晶两相结构组成,当UHMWPE粉末预热温度由室温28 ℃逐渐升高到85 ℃时,所成型出的微圆柱阵列塑件整体上由初生态和熔化再结晶两相结构变成为单相熔化再结晶结构。X射线衍射实验数据表明,micro-UPM微塑件基体部分的结晶度大于微圆柱部分的结晶度,且(110)晶面的晶粒尺寸大于(200)晶面的晶粒尺寸。

    Abstract:

    In this study, according to specific process parameters, micro ultra-high molecular weight polyethylene (UHMWPE) cylinder parts were molded by micro ultrasonic powder molding (micro-UPM) process using PCB inserts (printed circuit boards) of 150 μm micro-hole array. From the differential scanning calorimetry (DSC) and nanoindentation test results, if the UHMWPE powder is not preheated, then the micro-UPM cylinder array parts generally consist of nascent and melt-recrystallized phases as a whole. However, when the compressed UHMWPE powder grow from room temperature 28 ℃ to 85 ℃, the bio-phase structure gradually develops into single melt-recrystallized phase. According to single-crystal X-ray diffraction test result, the crystallinity degree of the base region of the micro-UPM cylinder array part is higher than that of the micro-cylinder region, whereas the grain size of the (110) crystal surface is larger than that of the (200) crystal surface.

    参考文献
    相似文献
    引证文献
引用本文

梁雄, 马将, 徐斌, 雷建国, 彭太江, 刘志远.超声粉末模压成型超高分子量聚乙烯微塑件的相结构演变规律[J].高分子材料科学与工程,2016,32(4):111-114. Xiong Liang, Jiang Ma, Bin Xu, Jianguo Lei, Taijiang Peng, Zhiyuan Liu. Phase Structure Development of Micro-UPM UHMWPE Parts[J]. Polymer Materials Science & Engineering,2016,32(4):111-114.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-04-19
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司