注水压力对圆管件水辅注塑填充过程的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51563010);江西省教育厅科技项目(GJJ14715,GJJ14718)


Influence of Water Injection Pressure on Water-Assisted Injection Molding Filling Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以开源代码OpenFOAM为基础,采用有限体积法和流体体积法构建了粘弹多相流的新求解器,数值模拟了圆管件的溢流法水辅注塑填充过程。基于熔体所固有的粘弹特性,解释了注水压力对熔体残余壁厚的影响,注水压力的变化导致熔体内变形速率的增加或减小,引起熔体抵抗变形能力的增强或减弱,直接影响到水相注入时受到阻力的大小,表现为熔体残余壁厚的多少。最后采用实验的方法进行验证,得出的结论与数值模拟所得的结论一致,并对数值大小的差异进行了解释。

    Abstract:

    Based on the open source code of OpenFOAM, a new solver for calculating viscoelastic multiphase flow was constructed by the finite volume method and the volume of fluid method. In this paper, the filling process of the overflow water-assisted injection molding(OWAIM) was simulated. The influence of water injection pressure on the melt residual thickness was explained based on the viscoelastic property. The value changes of water injection pressure lead to the value changes of deformation rate, which have the effect on the resist deformation ability. These changes directly affect the values of resistance when water is injected into the cavity and finally is showed by the values of melt residual thickness. Meanwhile, the analysis results are verified by experiments.

    参考文献
    相似文献
    引证文献
引用本文

章凯, 匡唐清, 柳和生, 余忠, 黄益宾, 董添文.注水压力对圆管件水辅注塑填充过程的影响[J].高分子材料科学与工程,2016,32(6):113-117. Kai Zhang, Tangqing Kuang, Hesheng Liu, Zhong Yu, Yibing Huang, Tianwen Dong. Influence of Water Injection Pressure on Water-Assisted Injection Molding Filling Process[J]. Polymer Materials Science & Engineering,2016,32(6):113-117.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-06-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司