聚对苯二甲酸丁二醇酯多孔纤维的制备及性能表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51273005);北京市教委科技发展计划重点项目暨北京自然科学基金资助重点项目(KZ201110012016);北京市教委青年拔尖人才项目(CIT&TCD201404023)


Preparation and Characterization of Poly (butylene terephthalate)Porous Fiber
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以聚对苯二甲酸丁二醇酯(PBT)、聚丙烯(PP)为原料,采用熔融纺丝法制备出PBT/PP共混海岛纤维,用二甲苯溶解剥离基体相PP,制得PBT多孔纤维。通过差示扫描量热分析、扫描电镜、X射线衍射和比表面积及孔径分析等测试,研究了共混纤维及多孔纤维的结构与性能。结果表明,当PBT和PP质量比为70/30时,共混纤维的相容性最好,且溶除后的多孔纤维孔容较大,孔径较小,一致性数值也较大即多孔纤维的尺寸单分散性好;最佳的溶除温度为120 ℃,时间为40min,浓度为1∶50。

    Abstract:

    The PBT/PP blending island fiber was prepared by melt spinning with raw material of poly (butylene terephthalate)(PBT) and polypropylene(PP), and the PBT porous fiber was formed in xylene solvent. The structure and properties of the blending fiber and the porous fiber were characterized by DSC, SEM, XRD and specific surface area and pore size. Results show that the compatibility of the blending fiber is the best when the mass ratio of PBT/PP is 70/30. After being dissolved, the porous fiber has bigger pore volume, smaller aperture, larger consistency of numerical namely good monodispersity of porous fibers; and the best dissolving temperature is 120 ℃, time is 40 min, concentration ratio is 1∶50.

    参考文献
    相似文献
    引证文献
引用本文

邵凤姣, 贾清秀, 张玉芳.聚对苯二甲酸丁二醇酯多孔纤维的制备及性能表征[J].高分子材料科学与工程,2016,32(6):148-153. Fengjiao Shao, Qingxiu Jia, Yufang Zhang. Preparation and Characterization of Poly (butylene terephthalate)Porous Fiber[J]. Polymer Materials Science & Engineering,2016,32(6):148-153.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-06-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司