聚丙烯发泡珠粒的结晶熔融行为与发泡特性
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(31270610)


Melting/Crystallization Behavior and Foaming Properties of Expanded Polypropylene Bead
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以CO2为发泡剂,用高压釜式法制备了发泡聚丙烯(EPP)珠粒。采用差示扫描量热仪和扫描电子显微镜探讨了发泡温度(Tf)和发泡压力(pf)对EPP结晶熔融行为和发泡特性的影响。结果表明,分别提高发泡温度或压力,EPP的熔融双峰均向高温方向移动,低温晶体与高温晶体的结晶度之比增大,而且温度对双峰的影响比压力更敏感。pf在2~4 MPa内,EPP的发泡倍率和泡孔密度随pf增大而增大;Tf在133.6~140 ℃间,发泡倍率和泡孔尺寸随Tf升高而变大,泡孔密度随Tf升高而变小。在Tf为133.6 ℃,pf为4 MPa时,EPP的熔融双峰结构比例合适,发泡倍率较大,泡孔密度最大且尺寸分布均匀、表面光滑。

    Abstract:

    Expended polypropylene (EPP) was prepared through autoclave foaming process, using CO2 as blowing agent. The influence of foaming temperature (Tf) and foaming pressure (pf) on melting/crystallization behavior and foaming properties of EPP were investigated by DSC and SEM. The results indicate that the double melting peaks of EPP move to higher temperature and the ratio of crystallinity between hightemperature crystal and lowtemperature crystal increases with increasing Tf or pf. Furthermore, the effect of Tf on double melting peaks of EPP becomes more sensitive than pf. When pf ranges from 2 MPa to 4 MPa, the expansion ratio and cell density of EPP increase with increasing pf. When Tf ranges from 133.6 ℃ to 140 ℃, the expansion ratio and cell size increase with increasing Tf, but the cell density decreases with increasing Tf. When Tf and pf are 133.6 ℃ and 4 MPa, respectively, EPP with desired double melting peaks, uniform cell structure and smooth surface is obtained. The cell density is the largest, and the distribution of cell size becomes the narrowest.

    参考文献
    相似文献
    引证文献
引用本文

熊业志, 刘月香, 胡圣飞, 陈哲, 刘清亭, 张荣.聚丙烯发泡珠粒的结晶熔融行为与发泡特性[J].高分子材料科学与工程,2016,32(9):49-53.]Yezhi Xiong, Yuexiang Liu, Shengfei Hu, Zhe Chen, Qingting Liu, Rong Zhang. Melting/Crystallization Behavior and Foaming Properties of Expanded Polypropylene Bead[J]. Polymer Materials Science & Engineering,2016,32(9):49-53.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-09-17
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司