等温准热压印中聚合物微结构成型的分析
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51173015,51673020)


Forming Analysis of Microstructure in Isothermal Quasi-Embossing Conditions
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    在传统平板微热压印中,模具需要反复的加热和冷却,工艺循环时间长,存在微结构成型效率低的缺点。文中创新性地提出一种等温准热压印工艺,可有效解决这一问题。首先在研究此工艺原理的基础上,采用有限元模拟的手段探究聚合物微结构的成型过程。模拟分析可知,聚合物微结构的成型是边冷却边压印的过程,模具温度显著影响微结构的复制精度;而聚合物基片预热温度过高不会提高微结构的复制精度,却增加了脱模缺陷的可能性。模拟得到的规律可为等温准热压印实验工艺参数的选取提供依据。最后通过实验验证了模拟规律的正确性及工艺的可行性。

    Abstract:

    In traditional flat micro thermal printing, since the mold requires repeated heating and cooling, the process cycle time is long and the forming efficiency is low. However, this problem can be effectively solved by the isothermal quasi-embossing technology innovatively proposed in this paper. Firstly, the finite element simulation method for the polymer microstructure forming was analyzed based on the introduced process principle. The simulation results show that the polymer microstructure forming is a process of cooling and embossing. The replication precision of the microstructure is significantly affected by the mold temperature, but not by the initial preheating temperature of the polymer substrate even at a high level, which increase the possibility of demolding defects. The simulation law for the isothermal quasi hot-pressing provides the theoretical reference to the selection of process parameters, which demonstrates the correctness of the simulation results and feasibility of the process.

    参考文献
    相似文献
    引证文献
引用本文

江冲,吴大鸣,刘颖,戴乐,孙靖尧,杨振洲,赵中里.等温准热压印中聚合物微结构成型的分析[J].高分子材料科学与工程,2016,32(10):105-111. Chong Jiang, Daming Wu, Ying Liu, Le Dai, Jingyao Sun, Zhenzhou Yang, Zhongli Zhao. Forming Analysis of Microstructure in Isothermal Quasi-Embossing Conditions[J]. Polymer Materials Science & Engineering,2016,32(10):105-111.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-10-14
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司