多巴胺改性聚四氟乙烯膜及表面固载溶菌酶
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(20806009);北京理工大学基础研究基金(20070542005)


Surface Modification of Polytetrafluoroethylene Membrane and Lysozyme Immobilization
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    用多巴胺对聚四氟乙烯膜表面改性,然后固定化溶菌酶,制备防水透气的抗菌材料。考察了改性条件对膜性能的影响,结果表明,随反应时间延长,膜表面氨基密度增加,接触角和气通量下降;12 h后,氨基密度和接触角均达到饱和。多巴胺浓度低于0.5 mg/mL时,膜表面氨基密度随着多巴胺浓度的增大而增加,接触角下降;多巴胺浓度超过1 mg/mL后,氨基密度和接触角基本不变。以溶壁微球菌为水解对象,探讨了固定化工艺条件对溶菌酶活力的影响。最优固定化条件为:戊二醛质量分数0.1%,酶浓度2 mg/mL,固定化时间8 h,pH值7.0。固载后的酶活最高可达3.5 U/cm2。X射线光电子能谱、衰减全反射傅里叶变换红外光谱和扫描电镜表征证实了聚多巴胺涂层的存在。用平板计数法测定了材料的抗菌性能,对金黄色葡萄球菌的抗菌率达到89%。

    Abstract:

    Polytetrafluoroethylene membrane was modified via self-polymerization of dopamine, and then lysozyme was immobilized on the surface of membrane, aiming at preparing waterproof and breathable antibacterial materials. The results show that with modification time increased, the surface animo groups density of membrane increases while the contact angle and gas flux decline. Animo group density and contact angle reach saturation after 12 h. With dopamine concentration increased within 0.5 mg/mL, the surface animo groups density of membrane increases while the contact angle declines, and they are substantially unchanged when the dopamine concentration exceeds 1 mg/mL. Effects of immobilization conditions on enzyme activity were measured by hydrolyzing micrococcus lysodeikticu cells. The optimum conditions are 0.1% glutaraldehyde, 2 mg/mL lysozyme, pH7.0 and 8 h reaction time. The maximum activity of immobilized lysozyme is 3.5 U/cm2. The results of FT-IR, SEM and XPS confirm the presence of polydopamine coating, and an antibacterial ratio of 89% is obtained.

    参考文献
    相似文献
    引证文献
引用本文

邢易, 魏利娜, 赵之平, 刘文芳.多巴胺改性聚四氟乙烯膜及表面固载溶菌酶[J].高分子材料科学与工程,2016,32(11):118-124. Yi Xing, Lina Wei, Zhiping Zhao, Wenfang Liu. Surface Modification of Polytetrafluoroethylene Membrane and Lysozyme Immobilization[J]. Polymer Materials Science & Engineering,2016,32(11):118-124.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-11-25
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司