官能团化碳纤维/热塑性聚氨酯复合泡沫材料的制备及力学性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

福建省科技厅引导性项目(2015H0016);福州市科技计划资助项目(2014-G-72)


Preparation and Mechanical Properties of Functional Groups of Carbon Fiber/Thermoplastic Polyurethane Foamed Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用浓H3PO4/浓HNO3混酸体系对碳纤维(CF)表面进行预处理得到酸化碳纤维,再利用二苯基甲烷二异氰酸酯(MDI)与酸化碳纤维发生接枝反应,制得官能团化碳纤维(MCF)。将其与热塑性聚氨酯(TPU)熔融共混得到MCF/TPU复合泡沫材料。利用红外光谱、X射线光电子能谱、X射线衍射、拉曼光谱和场发射扫描电镜等表征了纤维接枝改性效果和复合材料结构及断面形貌。结果表明,化学接枝使得纤维表面官能团化,并且接枝改性增加了纤维表面的粗糙度及无序程度。从而成功地改善了纤维和TPU基体的界面粘合力和相容性。力学性能分析表明,相比接枝前的CF,MCF可明显提高复合泡沫材料的力学性能,当纤维添加量为3%时,较改性前拉伸强度提高了16.1%,断裂伸长率提高了18.5%,撕裂强度提升了3.2%,回弹性提高了6.7%,压缩永久变形降低了6.9%。

    Abstract:

    The carbon fibers(CF) were pretreated with H3PO4/HNO3, and the acid-treated CF was obtained. After that, acid-treated CF was grafted with diphenyl methane diisocyanate(MDI), and the modified CF (MCF) was fabricated. subsequently, the MCF/thermoplastic polyurethane(TPU) composite foamed materials could be prepared through the addition of MCF into TPU matrix. The surface characteristics of modified CF,the structures properties and section morphology of foamed composites were investigated by FT-IR, XPS, XRD,Raman and FESEM. The results show that chemical grafting can gain functional groups, high roughness and disorder of carbon fibers, which can improve the compatibility and interface bonding strength between carbon fibers and TPU. Compared to 3% CF/TPU, the tensile strength, elongation at break, tear strength, rebound resilience of 3% MCF/TPU are increased by 16.1%, 18.5%, 4.5%, 6.7% respectively, whereas the compression set is reduced by 6.9%.

    参考文献
    相似文献
    引证文献
引用本文

连汉青, 郑玉婴, 邱洪峰, 张延兵.官能团化碳纤维/热塑性聚氨酯复合泡沫材料的制备及力学性能[J].高分子材料科学与工程,2016,32(12):126-132. Hanqing Lian, Yuying Zheng, Hongfeng Qiu, Yanbing Zhang. Preparation and Mechanical Properties of Functional Groups of Carbon Fiber/Thermoplastic Polyurethane Foamed Composites[J]. Polymer Materials Science & Engineering,2016,32(12):126-132.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-12-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司