聚丙烯/线型低密度聚乙烯开孔泡沫的制备及吸油性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51473181);浙江省自然科学基金资助项目(LQ14E030006);宁波市自然科学基金资助项目(2014A610131)


Preparation of Open-cell Polypropylene/Linear Low Density Polyethylene Blend Foams and the Oil Sorption Performance
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以超临界二氧化碳为发泡剂,通过连续挤出发泡法制备聚丙烯/线型低密度聚乙烯(PP/LLDPE)共混物开孔泡沫,并用于吸油性能研究。文中系统研究了发泡温度、原料配比和口模直径对PP/LLDPE泡沫开孔结构和吸油倍率的影响,并研究了泡沫的亲油疏水性和吸油的重复使用性。结果表明,当发泡温度为170 ℃,LLDPE的含量为10%,口模直径为0.5 mm时,发泡样品的密度低、开孔率高、吸油倍率高;PP/LLDPE泡沫对水的接触角为137.8°,疏水性能好;对机油10次重复使用后仍具有很高的吸油倍率。因此,该复合开孔泡沫在污水处理、溢油事故和环境保护中具有潜在的应用价值。

    Abstract:

    Open-cell polypropylene/linear low density polyethylene (PP/LLDPE) blend foams were prepared via continuous extrusion with supercritical carbon dioxide. The effect of foaming temperature, LLDPE content and die diameter on the open-cell structure and oil sorption performance of PP/LLDPE foams were investigated. The oleophilic-hydrophobic properties and reusability were also studied. The results show that PP/LLDPE foams exhibit low density, high open-cell content and high oil sorption capacity at the foaming temperature of 170 ℃, LLDPE content of 10% and die diameter of 0.5 mm. A drop of water on PP/LLDPE foam forms a contact angle of 137.8°, indicating that the open-cell foam exhibits excellent hydrophobicity. When PP/LLDPE foam is repetitively used for ten times, it still shows a high sorption capacity with the motor oil. Based on this study, PP/LLDPE open-cell foams have showed great potential for wide applications in wastewater treatment, oil accident remediation and environmental protection.

    参考文献
    相似文献
    引证文献
引用本文

王舒生, 王坤, 庞永艳, 吴飞, 郑文革, 王邃.聚丙烯/线型低密度聚乙烯开孔泡沫的制备及吸油性能[J].高分子材料科学与工程,2016,32(12):133-138. Shusheng Wang, Kun Wang, Yongyang Pang, Fei Wu, Wenge Zheng, Sui Wang. Preparation of Open-cell Polypropylene/Linear Low Density Polyethylene Blend Foams and the Oil Sorption Performance[J]. Polymer Materials Science & Engineering,2016,32(12):133-138.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2016-12-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司