桐油基环氧增塑剂的合成及在聚氯乙烯中的应用
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

“十二五”国家科技支撑计划资助(2015BAD15B08);江苏省生物质能源与材料重点实验室基本科研业务费(JSDEM-S-201604)


Synthesis of Tung Oil Based Epoxy Plasiticizer and Its Application in Poly (vinyl chloride)
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    将合成的目标产物环氧桐马甲酯二异辛酯(EDOMEM)与邻苯二甲酸二辛酯(DOP)复配使用增塑聚氯乙烯(PVC)。采用红外光谱对EDOMEM结构进行表征,采用热重分析、热重-红外、热重-质谱、转矩流变仪、万能拉力等测试对共混试样进行了分析。结果表明,相比于试样F0,F4的Ti、T10、T50分别提高了5.6 ℃、12.6 ℃和25.4 ℃;TGA-FT-IR和TGA-MS说明PVC共混物热降解过程中的主要气体为H2O、CO、HCl、CO2和C6H6;当EDOMEM的含量由0%增加到33.3%(占增塑剂总质量百分比)时,断裂伸长率提高了9%,使得体系柔韧性得以改善;动态热稳定性由原来的12.1 min延长至40.2 min,加工稳定性能更好;此外,随着EDOMEM含量增加,挥发性和抽出性损失降低,增塑剂在塑料制品中的稳定性得以改善。因此,EDOMEM可以作为PVC的一种良好的辅助增塑剂使用。

    Abstract:

    The target product epoxidized diisooctyl methyl-α-eleostearate maleate (EDOMEM) was obtained and then blended with dioctyl-phthalate (DOP) used as complex plasticizer to plasticize poly (vinyl chloride) (PVC). And EDOMEM was characterized by FT-IR. TGA, TGA-FT-IR, TGA-MS, torque rheometer and the mechanical properities were used for evaluating the PVC blends. The results indicate that the initial thermal degradation temperature (Ti), the 10% mass loss temperature (T10) and the 50% mass loss temperature (T50) respectively increase 5.6 ℃, 12.6 ℃ and 25.4 ℃ compared with F0. TGA-FT-IR and TGA-MS detect that the main pyrolysis products of PVC blends are H2O, CO, HCl, CO2 and C6H6. When the EDOMEM content increases from 0% to 33.3% (the total quality of plasticizer), the elongation at break raises 9%, improving flexibility of the PVC blends. The dynamic stability time is prolonged from 12.11 min to 40.24 min. Moreover, the loss of voalitity and extraction decrease with the content of EDOMEM increasing. Therefore, EDOMEM can be used as secondary plasiticizer for PVC.

    参考文献
    相似文献
    引证文献
引用本文

李小英, 聂小安, 陈洁, 王义刚.桐油基环氧增塑剂的合成及在聚氯乙烯中的应用[J].高分子材料科学与工程,2017,33(2):28-33. Xiaoying Li, Xiaoan Nie, Jie Chen, Yigang Wang. Synthesis of Tung Oil Based Epoxy Plasiticizer and Its Application in Poly (vinyl chloride)[J]. Polymer Materials Science & Engineering,2017,33(2):28-33.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-02-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司