密胺树脂多孔材料的制备及对二氧化碳的吸附
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Preparation and CO2 Adsorption Application of Porous Melamine Materials
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以三聚氰胺与甲醛为原料,二甲苯为分散相,利用浓乳液模板法合成了密胺树脂多孔材料。研究了预聚过程以及不同单体配比、分散相体积分数和乳化剂用量对密胺树脂多孔材料结构的影响。结果表明,当预聚温度为75 ℃,预聚时间为20 min,预聚体系pH值为8时,得到的预聚物可以制备出稳定的浓乳液。当单体配比n(三聚氰胺)∶n(甲醛)=1∶3,分散相体积分数为85%,乳化剂的量为20%时,可以制备出比表面积为3.317 m2/g的密胺树脂多孔材料。所制备的多孔材料可用于吸附二氧化碳,最大吸附量为60.3 mg/g。

    Abstract:

    Porous melamine resin was prepared by the concentrated emulsion polymerization with melamine and formaldehyde as raw material and dimethyl benzene as dispersed phase. The influence of the per-polymerization process, including the ratio of monomers, the volume fraction of dispersed phase and the content of emulsifier on the porous structure of melamine-formaldehyde materials were discussed. The results indicate that when the temperature is 75 ℃, the per-polymerization time is 20 min, and the pH value is 8, the stable concentrated emulsion of obtained pre-polymer could be achieved. When n(melamine)∶n(formaldehyde) is 1∶3, the volume fraction of dispersed phase is 85% and the content of emulsifier is 20%, the porous melamine resin with the Brunauer-Emmett-Teller surface area of 3.317 m2/g is obtained. The maximum CO2 adsorbance of the obtained porous melamine resin reaches 60.3 mg/g.

    参考文献
    相似文献
    引证文献
引用本文

陈东, 段成, 杜中杰, 励杭泉, 张晨.密胺树脂多孔材料的制备及对二氧化碳的吸附[J].高分子材料科学与工程,2017,33(2):39-43. Dong Chen, Cheng Duan, Zhongjie Du, Hangquan Li, Chen Zhang. Preparation and CO2 Adsorption Application of Porous Melamine Materials[J]. Polymer Materials Science & Engineering,2017,33(2):39-43.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-02-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司